- 您现在的位置：买卖IC网 > PDF目录19528 > NCP1201D100R2 (ON Semiconductor)IC CTRLR PWM CM OTP 8SOIC PDF资料下载
参数资料
| 型号： | NCP1201D100R2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 11/19页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM CM OTP 8SOIC |
| 产品变化通告： | LTB Notification 03/Jan/2008 |
| 标准包装： | 2,500 |
| 输出隔离： | 隔离 |
| 频率范围： | 92kHz ~ 117kHz |
| 输入电压： | 12.5 V ~ 16 V |
| 输出电压： | 500V |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
NCP1201
Our power contribution example drops to 223 V x 2.1 m
= 468.3 mW. If a resistor is installed between the mains and
the diode, you further force the dissipation to migrate from
the package to the resistor. The resistor value should be
carefully selected to account for low--line startup.
HV
Skipping Cycle Mode
The NCP1201 automatically skips switching cycles when
the output power demand drops below a preset level. This is
accomplished by monitoring the FB pin. In normal
operation, FB pin imposes a peak current according to the
load value. If the load demand decreases, the internal loop
asks for less peak current. When this set--point reaches the
skip mode threshold level, 1.07 V, the IC prevents the
current from decreasing further down and starts to blank the
Mains
Cbulk
1
2
3
4
8
7
6
5
output pulses, i.e. the controller enters the so--called Skip
Cycle Mode, also named Controlled Burst Operation. The
power transfer now depends upon the width of the pulse
bunches, Figure 29.
Suppose we have the following component values:
Lp , primary inductance = 1.0 mH
F sw , switching frequency = 60 kHz
1 × L × I 2 × F
sw = 1.2 W
p
p
Figure 28. A Simple Diode Naturally Reduces the
Average Voltage on Pin 8
3. Permanently force the V CC level above VCC OFF
with an auxiliary winding. It will automatically
disconnect the internal startup source and the IC
will be fully self--supplied from this winding.
Again, the total power drawn from the mains will
significantly decrease. By using this approach,
user need to make sure the auxiliary voltage never
I p (skip) = 200 mA (or 333 mV/R sense )
The theoretical power transfer is therefore:
(eq. 4)
2
If the controller enters Skip Cycle Mode with a pulse packet
length of 20 ms over a recurrent period of 100 ms, then the
total power transfer reduced to 1.2 W x 0.2 = 240 mW.
To better understand how this Skip Cycle Mode takes
place, a look at the operation mode versus the FB pin voltage
level shown below, immediately gives the necessary insight.
exceeds the 16 V limit for all line conditions.
FB
4.2 V, FB Pin Open
2.97 V, Upper Dynamic Range
Normal Current Mode Operation
Skip Cycle Operation
1.07 V
I p(min) = 333 mV / R sense
Figure 29. Feedback Pin Voltage and Modes of Operation
When FB pin voltage level is above the skip cycle threshold
(1.07 V by default), the peak current cannot exceed
0.9 V/R sense . When the IC enters the skip cycle mode, the
peak current cannot go below V SKIP /3.3. By using the peak
current limit reduction scheme, the skip cycle takes place at
a lower peak current, which guarantees noise free operation.
http://onsemi.com
11
相关PDF资料 |
PDF描述 |
|---|---|
| ESA50DTBS | CONN EDGECARD 100PS R/A .125 SLD |
| EPM7064STI100-7N | IC MAX 7000 CPLD 64 100-TQFP |
| GBM10DTAT | CONN EDGECARD 20POS R/A .156 SLD |
| PR6002-T | DIODE FAST REC 6A 100V R-6 |
| NCP1014ST65T3 | IC OFFLINE SWIT SMPS CM SOT223 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1201D100R2G | 功能描述:电流型 PWM 控制器 ANALOG POWER CONV RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1201D60R2 | 功能描述:电流型 PWM 控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1201D60R2G | 功能描述:电流型 PWM 控制器 Current Mode PWM w/Fault Protection RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1201P100 | 功能描述:电流型 PWM 控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1201P100G | 功能描述:电流型 PWM 控制器 Current Mode PWM w/Fault Protection RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。