- 您现在的位置：买卖IC网 > PDF目录19624 > NCP1230P100G (ON Semiconductor)IC CTRLR PWM SMPS OVP OCP 7DIP PDF资料下载
参数资料
| 型号： | NCP1230P100G |
| 厂商： | ON Semiconductor |
| 文件页数： | 12/21页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM SMPS OVP OCP 7DIP |
| 标准包装： | 50 |
| 输出隔离： | 隔离 |
| 频率范围： | 100kHz |
| 输入电压： | 8.4 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm），7 引线 |
| 供应商设备封装： | 7-PDIP |
| 包装： | 管件 |
NCP1230
Ipk + 0.75
Feedback
The feedback pin has been designed to be connected
directly to the open ? collector output of an optocoupler. The
pin is pulled ? up through a 20 k W resistor to the internal
Vdd_fb supply (5 volts nominal). The feedback input signal
where:
Rs @ 3
Ipk @ Rs + 1V
2 @ Pin
Lp @ f
is divided down, by a factor of three, and connected to the
negative ( ? ) input of the PWM comparator. The positive (+)
input to the PWM comparator is the current sense signal
(Figure 30).
The NCP1230 is a peak current mode controller, where
the feedback signal is proportional to the output power. At
the beginning of the cycle, the power switch is turns ? on and
the current begins to increase in the primary of the
Ipk +
where:
P in = is the power level where the NCP1230 will go into
the skip mode
L p = Primary inductance
f = NCP1230 controller frequency
Pin + p
Pin + Pout
transformer, when the peak current crosses the feedback
voltage level, the PWM comparators switches from a logic
level low, to a logic level high, resetting the PWM latching
Flip ? Flop, turning off the power switch until the next
oscillator clock cycle begins.
where:
L @ f @ Ipk2
2
Eff
Vdd_fb
Eff = the power supply efficiency
Rout + Eout
2
FB
20k
55k
10 V
25k
?
+
PWM
Vskip
2
Pout
S is rising edge triggered
R is falling edge triggered
/ Vstby ? out
2.3 Vpp
Ramp
+
1.25 V
+
?
125 ms
S
R
18k
3
LEB
Vdd_fb
Figure 30.
The feedback pin input is clamped to a nominal 10 volt for
ESD protection.
Skip Mode
FB
Vskip
+
0.75 V
?
+
PFC_V CC
Latch
Reset
The feedback input is connected in parallel with the skip
cycle logic (Figure 31). When the feedback voltage drops
below 25% of the maximum peak current (1.0 V/Rsense) the
IC prevents the current from decreasing any further and
starts to blank the output pulses. This is called the skip cycle
mode. While the controller is in the burst mode the power
transfer now depends upon the duty cycle of the pulse burst
width which reduces the average input power demand.
Vc + Ipk @ Rs @ 3
where:
V c = control voltage (Feedback pin input),
I pk = Peak primary current,
R s = Current sense resistor,
3 = Feedback divider ratio.
SkipLevel + 3V @ 25% + 0.75V
CS Cmp
Figure 31.
During the skip mode the PFC_Vcc signal (pin 1) is
asserted into a high impedance state when a light load
condition is detected and confirmed, Figure 32 shows
typical waveforms. The first section of the waveform shows
a normal startup condition, where the output voltage is low,
as a result the feedback signal will be high asking the
controller to provide the maximum power to the output. The
second phase is under normal loading, and the output is in
regulation. The third phase is when the output power drops
below the 25% threshold (the feedback voltage drops to 0.75
volts). When this occurs, the 125 msec timer starts, and if the
conditions is still present after the time output period, the
http://onsemi.com
12
相关PDF资料 |
PDF描述 |
|---|---|
| V150A48E400BG2 | CONVERTER MOD DC/DC 48V 400W |
| R2D12-2405/HP | CONV DC/DC 2W +/-5VOUT SMD |
| DEHR33A221KA2B | CAP CER 220PF 1KV 10% RADIAL |
| F751A337KDC | CAP TANT 330UF 10V 10% 2917 |
| R2D12-2412/HP | CONV DC/DC 2W +/-12VOUT SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1230P133 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1230P133G | 功能描述:电流型 PWM 控制器 Low Standby Power High Performance PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1230P65 | 功能描述:交流/直流开关转换器 Low Standby Power RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| NCP1230P65G | 功能描述:电流型 PWM 控制器 Low Standby Power High Performance PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1231 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Low−Standby Power High Performance PWM Controller |
发布紧急采购，3分钟左右您将得到回复。