- 您现在的位置：买卖IC网 > PDF目录13774 > NCP1522BSNT1G (ON Semiconductor)IC REG BUCK SYNC ADJ 0.6A 5TSOP PDF资料下载
参数资料
| 型号： | NCP1522BSNT1G |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.6A 5TSOP |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.9 V ~ 3.3 V |
| 输入电压： | 2.7 V ~ 5.5 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 3MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSOP（0.059"，1.50mm 宽）5 引线 |
| 包装： | 标准包装 |
| 供应商设备封装： | 5-TSOP |
| 其它名称： | NCP1522BSNT1GOSDKR |
NCP1522B
Soft ? Start
The NCP1522B uses soft ? start to limit the inrush current
when the device is initially powered up or enabled.
Soft ? start is implemented by gradually increasing the
reference voltage until it reaches the full reference voltage.
During startup, a pulsed current source charges the internal
soft ? start capacitor to provide gradually increasing
reference voltage. When the voltage across the capacitor
ramps up to the nominal reference voltage, the pulsed
current source will be switched off and the reference
voltage will switch to the regular reference voltage.
Cycle ? by ? Cycle Current Limitation
From the block diagram, an I LIM comparator is used to
realize cycle ? by ? cycle current limit protection. The
comparator compares the LX pin voltage with the
reference voltage, which is biased by a constant current. If
the inductor current reaches the limit, the I LIM comparator
detects the LX voltage falling below the reference voltage
and releases the signal to turn off the switch Q1. The
cycle ? by ? cycle current limit is set at 1200 mA (nom).
Low Dropout Operation
The NCP1522B offers a low input to output voltage
difference. The NCP1522B can operate at 100% duty
cycle. In this mode the PMOS (Q1) remains completely on.
The minimum input voltage to maintain regulation can
be calculated as:
VIN(min) + VOUT(max)
) (IOUT (RDS(ON) ) RINDUCTOR))
(eq. 1)
? V OUT : Output Voltage (Volts)
? I OUT : Max Output Current
? R DS(ON) = P ? Channel Switch R DS(ON)
? R INDUCTOR : Inductor Resistance (DCR)
Undervoltage Lockout
The input voltage V IN must reach 2.4 V (typ) before the
NCP1522B enables the DC/DC converter output to begin
the start up sequence (see Soft ? Start section). The UVLO
threshold hysteresis is typically 100 mV.
Shutdown Mode
Forcing this pin to a voltage below 0.4 V will shut down
the IC. In shutdown mode, the internal reference, oscillator
and most of the control circuitries are turned off. Therefore,
the typical current consumption will be 0.3 m A (typical
value). Applying a voltage above 1.2 V to EN pin will
enable the device for normal operation. The typical
threshold is around 0.7 V. The device will go through
soft ? start to normal operation.
Thermal Shutdown
Internal Thermal Shutdown circuitry is provided to
protect the integrated circuit in the event that the maximum
junction temperature is exceeded. If the junction
temperature exceeds 160 ° C, the device shuts down. In this
mode switch Q1 and Q2 and the control circuits are all
turned off. The device restarts in soft ? start after the
temperature drops below 135 ° C. This feature is provided
to prevent catastrophic failures from accidental device
overheating, and it is not intended as a substitute for proper
heatsinking.
Short Circuit Protection
When the output is shorted to ground, the device limits
the inductor current. The duty ? cycle is minimum and the
consumption on the input line is 300 mA (Typ). When the
short circuit condition is removed, the device returns to the
normal mode of operation.
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| RSM12DTMS | CONN EDGECARD 24POS R/A .156 SLD |
| RCM28DTMH | CONN EDGECARD 56POS R/A .156 SLD |
| RBM25DTMH | CONN EDGECARD 50POS R/A .156 SLD |
| RBM25DTMD | CONN EDGECARD 50POS R/A .156 SLD |
| RCM28DTMD | CONN EDGECARD 56POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1522BUEVB | 功能描述:电源管理IC开发工具 NCP1522 EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1522BUGEVB | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1523BFCT2G | 功能描述:直流/直流开关转换器 FORCED PWM NCP1523 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1523BGEVB | 功能描述:电源管理IC开发工具 NCP1523B EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1523FCT2G | 功能描述:直流/直流开关转换器 UBUMP DCDC RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。