- 您现在的位置：买卖IC网 > PDF目录14683 > NCP1529MUTBG (ON Semiconductor)IC REG BUCK SYNC ADJ 1A 6UDFN PDF资料下载
参数资料
| 型号： | NCP1529MUTBG |
| 厂商： | ON Semiconductor |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 1A 6UDFN |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.9 V ~ 3.9 V |
| 输入电压： | 2.7 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.7MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-UDFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 6-uDFN（2x2） |
| 其它名称： | NCP1529MUTBGOSDKR |
NCP1529
Soft ? Start
The NCP1529 uses soft ? start to limit the inrush current
when the device is initially powered up or enabled. Soft start
is implemented by gradually increasing the reference
voltage until it reaches the full reference voltage. During
startup, a pulsed current source charges the internal
soft ? start capacitor to provide gradually increasing
reference voltage. When the voltage across the capacitor
ramps up to the nominal reference voltage, the pulsed
current source will be switched off and the reference voltage
will switch to the regular reference voltage.
Cycle ? by ? cycle Current Limitation
From the block diagram, an I LIM comparator is used to
realize cycle ? by ? cycle current limit protection. The
comparator compares the SW pin voltage with the reference
voltage, which is biased by a constant current. If the inductor
current reaches the limit, the I LIM comparator detects the
SW voltage falling below the reference voltage and releases
temperature exceeds 180 ° C, the device shuts down. In this
mode all power transistors and control circuits are turned
off. The device restarts in soft ? start after the temperature
drops below 140 ° C. This feature is provided to prevent
catastrophic failures from accidental device overheating.
Short Circuit Protection
When the output is shorted to ground, the device limits the
inductor current. The duty ? cycle is minimum and the
consumption on the input line is 550 mA (typ). When the
short circuit condition is removed, the device returns to the
normal mode of operation.
USB or 5 V Rail Powered Applications
For USB or 5 V rail powered applications, NCP1529 is
able to supply voltages up to 3.9 V, 600 mA, operating in
PWM mode only, with high efficiency (Figure 28), low
output voltage ripple and good load regulation results over
all current range (Figure 29).
the signal to turn off the switch Q1. The cycle ? by ? cycle
current limit is set at 1600 mA (nom).
Low Dropout Operation
The NCP1529 offers a low input to output voltage
difference. The NCP1529 can operate at 100% duty cycle.
In this mode the PMOS (Q1) remains completely ON. The
minimum input voltage to maintain regulation can be
calculated as:
V out + V OUT(max) ) I OUT R DS(on) _R INDUCTOR
(eq. 1)
100
95
90
85
80
75
70
65
60
55
50
25 ° C
? 40 ° C
85 ° C
?
?
?
?
V OUT : Output Voltage (V)
I OUT : Max Output Current
R DS(on) : P ? Channel Switch R DS(on)
R INDUCTOR : Inductor Resistance (DCR)
45
40
0
200 400 600 800
I OUT , OUTPUT CURRENT (mA)
Figure 28. Efficiency vs. Output Current
1000
85 ° C
Undervoltage Lockout
The Input voltage V IN must reach 2.4 V (typ) before the
NCP1529 enables the DC/DC converter output to begin the
start up sequence (see soft ? start section). The UVLO
threshold hysteresis is typically 100 mV.
Shutdown Mode
Forcing this pin to a voltage below 0.4 V will shut down
the IC. In shutdown mode, the internal reference, oscillator
and most of the control circuitries are turned off. Therefore,
the typical current consumption will be 0.3 m A (typical
value). Applying a voltage above 1.2 V to EN pin will enable
the DC/DC converter for normal operation. The device will
go through soft ? start to normal operation.
Thermal Shutdown
Internal Thermal Shutdown circuitry is provided to
protect the integrated circuit in the event that the maximum
junction Temperature is exceeded. If the junction
3.0
2.5
2.0
1.5
1.0
0.5
0.0
? 0.5
? 1.0
? 1.5
? 2.0
? 2.5
? 3.0
(V IN = 5.0 V, V OUT = 3.9 V)
? 40 ° C
25 ° C
0 200 400 600 800 1000
I OUT , OUTPUT CURRENT (mA)
Figure 29. Load Regulation vs. Output Current
(V IN = 5.0 V, V OUT = 3.9 V)
http://onsemi.com
11
相关PDF资料 |
PDF描述 |
|---|---|
| 380LQ391M350H052 | CAP ALUM 390UF 350V 20% SNAP |
| SLPX102M250H5P3 | CAP ALUM 1000UF 250V 20% SNAP |
| 381LX680M400K202 | CAP ALUM 68UF 400V 20% SNAP |
| 381LX391M250J032 | CAP ALUM 390UF 250V 20% SNAP |
| 381LQ561M250H452 | CAP ALUM 560UF 250V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1529MUTBGEVB | 功能描述:电源管理IC开发工具 NCP1529 EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1530DM25R2 | 功能描述:直流/直流开关转换器 600mA PWM/PFM Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1530DM25R2G | 功能描述:直流/直流开关转换器 600mA PWM/PFM Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1530DM27R2 | 功能描述:直流/直流开关转换器 600mA PWM/PFM Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1530DM27R2G | 功能描述:直流/直流开关转换器 600mA PWM/PFM Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。