- 您现在的位置：买卖IC网 > PDF目录20427 > NCP1529MUTBGEVB (ON Semiconductor)EVAL BOARD FOR NCP1529MUTBG PDF资料下载
参数资料
| 型号： | NCP1529MUTBGEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR NCP1529MUTBG |
| 设计资源： | NCP1529MUTBGEVB BOM NCP1529MUTBGEVB Gerber Files NCP1529MUTBGEVB Schematic |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 0.9 V ~ 3.9 V |
| 电流 - 输出： | 1A |
| 输入电压： | 3.6V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 1.7MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | NCP1529 |
| 其它名称： | NCP1529MUTBGEVBOS |
NCP1529
Soft ? Start
The NCP1529 uses soft ? start to limit the inrush current
when the device is initially powered up or enabled. Soft start
is implemented by gradually increasing the reference
voltage until it reaches the full reference voltage. During
startup, a pulsed current source charges the internal
soft ? start capacitor to provide gradually increasing
reference voltage. When the voltage across the capacitor
ramps up to the nominal reference voltage, the pulsed
current source will be switched off and the reference voltage
will switch to the regular reference voltage.
Cycle ? by ? cycle Current Limitation
From the block diagram, an I LIM comparator is used to
realize cycle ? by ? cycle current limit protection. The
comparator compares the SW pin voltage with the reference
voltage, which is biased by a constant current. If the inductor
current reaches the limit, the I LIM comparator detects the
SW voltage falling below the reference voltage and releases
temperature exceeds 180 ° C, the device shuts down. In this
mode all power transistors and control circuits are turned
off. The device restarts in soft ? start after the temperature
drops below 140 ° C. This feature is provided to prevent
catastrophic failures from accidental device overheating.
Short Circuit Protection
When the output is shorted to ground, the device limits the
inductor current. The duty ? cycle is minimum and the
consumption on the input line is 550 mA (typ). When the
short circuit condition is removed, the device returns to the
normal mode of operation.
USB or 5 V Rail Powered Applications
For USB or 5 V rail powered applications, NCP1529 is
able to supply voltages up to 3.9 V, 600 mA, operating in
PWM mode only, with high efficiency (Figure 28), low
output voltage ripple and good load regulation results over
all current range (Figure 29).
the signal to turn off the switch Q1. The cycle ? by ? cycle
current limit is set at 1600 mA (nom).
Low Dropout Operation
The NCP1529 offers a low input to output voltage
difference. The NCP1529 can operate at 100% duty cycle.
In this mode the PMOS (Q1) remains completely ON. The
minimum input voltage to maintain regulation can be
calculated as:
V out + V OUT(max) ) I OUT R DS(on) _R INDUCTOR
(eq. 1)
100
95
90
85
80
75
70
65
60
55
50
25 ° C
? 40 ° C
85 ° C
?
?
?
?
V OUT : Output Voltage (V)
I OUT : Max Output Current
R DS(on) : P ? Channel Switch R DS(on)
R INDUCTOR : Inductor Resistance (DCR)
45
40
0
200 400 600 800
I OUT , OUTPUT CURRENT (mA)
Figure 28. Efficiency vs. Output Current
1000
85 ° C
Undervoltage Lockout
The Input voltage V IN must reach 2.4 V (typ) before the
NCP1529 enables the DC/DC converter output to begin the
start up sequence (see soft ? start section). The UVLO
threshold hysteresis is typically 100 mV.
Shutdown Mode
Forcing this pin to a voltage below 0.4 V will shut down
the IC. In shutdown mode, the internal reference, oscillator
and most of the control circuitries are turned off. Therefore,
the typical current consumption will be 0.3 m A (typical
value). Applying a voltage above 1.2 V to EN pin will enable
the DC/DC converter for normal operation. The device will
go through soft ? start to normal operation.
Thermal Shutdown
Internal Thermal Shutdown circuitry is provided to
protect the integrated circuit in the event that the maximum
junction Temperature is exceeded. If the junction
3.0
2.5
2.0
1.5
1.0
0.5
0.0
? 0.5
? 1.0
? 1.5
? 2.0
? 2.5
? 3.0
(V IN = 5.0 V, V OUT = 3.9 V)
? 40 ° C
25 ° C
0 200 400 600 800 1000
I OUT , OUTPUT CURRENT (mA)
Figure 29. Load Regulation vs. Output Current
(V IN = 5.0 V, V OUT = 3.9 V)
http://onsemi.com
11
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BNJ-CX-F4 | CONVERTER MOD DC/DC 36V 75W |
| VF20120SG-E3/45 | DIODE SCHOTTKY 20A 120V ITO220AB |
| ECM08DRES | CONN EDGECARD 16POS .156 EYELET |
| REC5-0505SRW/H2/A | CONV DC/DC 5W 4.5-9VIN 05VOUT |
| EBC15DREF-S13 | CONN EDGECARD 30POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1530DM25R2 | 功能描述:直流/直流开关转换器 600mA PWM/PFM Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1530DM25R2G | 功能描述:直流/直流开关转换器 600mA PWM/PFM Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1530DM27R2 | 功能描述:直流/直流开关转换器 600mA PWM/PFM Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1530DM27R2G | 功能描述:直流/直流开关转换器 600mA PWM/PFM Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCP1530DM30R2 | 功能描述:直流/直流开关转换器 600mA PWM/PFM Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。