- 您现在的位置：买卖IC网 > PDF目录15054 > NCP1583DR2G (ON Semiconductor)IC REG CTRLR BUCK PWM VM 8-SOIC PDF资料下载
参数资料
| 型号： | NCP1583DR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 6/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 8-SOIC |
| 产品变化通告： | Product Discontinuation 01/Oct/2008 |
| 标准包装： | 2,500 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 325kHz |
| 占空比： | 80% |
| 电源电压： | 4.5 V ~ 13.2 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
NCP1582, NCP1582A, NCP1583
DETAILED OPERATING DESCRIPTION
General
The NCP158x is an 8 ? pin PWM controller intended for
1.1 V
DC ? DC conversion from 5.0 V & 12 V buses. The NCP158x
has a 0.7 A internal gate driver circuit designed to drive
N ? channel MOSFETs in a synchronous ? rectifier buck
topology. The output voltage of the converter can be
V comp
Enable
0.4 V
0.4 V
precisely regulated down to 800 mV 1.5% when the V FB pin
is tied to V OUT . The switching frequency is internally set. A
high gain operational transconductance error amplifier
(OTA) is used.
Duty Cycle and Maximum Pulse Width Limits
In steady state DC operation, the duty cycle will stabilize
at an operating point defined by the ratio of the input to the
output voltage. The NCP158x can achieve an 80% duty
cycle. There is a built in off ? time which ensures that the
V fb
Isource/
Sink
10 m A
-10 m A
Start Up
SS
120 m A
Normal
10 m A
bootstrap supply is charged every cycle. The NCP158x,
which is capable of a 100 nsec pulse width (min.), can allow
a 12 V to 0.8 V conversion at 350 kHz.
Input Voltage Range (V CC and BST)
The input voltage range for both V CC and BST is 4.5 V to
13.2 V with respect to GND and PHASE, respectively.
Although BST is rated at 13.2 V with respect to PHASE, it
can also tolerate 26.5 V with respect to GND.
External Enable/Disable
When the Comp pin voltage falls or is pulled externally
below the 400 mv threshold, it disables the PWM Logic and
the gate drive outputs. In this disabled mode, the operational
transconductance error amplifier ’s (EOTA) output source
current is reduced and limited to the Soft Start current of 10 m A.
Normal Shutdown Behavior
Normal shutdown occurs when the IC stops switching
because the input supply reaches UVLO threshold. In this
case, switching stops, the internal SS is discharged, and all
GATE pins go low. The switch node enters a high impedance
state and the output capacitors discharge through the load
with no ringing on the output voltage.
External Soft Start
The NCP158x features an external soft start function,
which reduces inrush current and overshoot of the output
voltage. Soft start is achieved by using the internal current
source of 10 m A. (typ), which charges the external integrator
capacitor of the transconductance amplifier. Figure 10 is a
typical soft start sequence. This sequence begins once V CC
surpasses its UVLO threshold. During Soft Start, as the
Comp Pin rises through 400 mV, the PWM Logic and gate
drives are enabled. When the feedback voltage crosses
800 mV, the EOTA will be given control to switch to its
higher regulation mode output current of 120 m A. In the
event of an overcurrent during soft start, the overcurrent
logic will override the soft start sequence and will shut down
the PWM logic and both the high side and low side gates.
Timing Diagram NCP1582: Enable Sequence
Figure 10. Soft Start Implementation
UVLO
Under Voltage Lockout (UVLO) is provided to ensure that
unexpected behavior does not occur when V CC is too low to
support the internal rails and power the converter. For the
NCP158x, the UVLO is set to ensure that the IC will start up
when V CC reaches 4.2 V and shutdown when V CC drops
below 3.7 V. This permits operation when converting from
a 5.0 input voltage.
Current Limit Protection
In case of a short circuit or overload, the low ? side (LS)
FET will conduct large currents. The controller will shut
down the regulator in this situation for protection against
overcurrent. The low ? side R DSon sense is implemented by
comparing the voltage at the Phase node when BG starts
going low to an internally generated fixed voltage. If the
phase voltage is lower than SCP trip voltage, an overcurrent
condition occurs and a counter is initiated. When the counter
completes, the PWM logic and both HS ? FET and LS ? FET
are turned off. The controller will retry to see if the short
circuit or overload condition is removed through the soft
start cycle. The minimum turn ? on time of the LS ? FET is set
to be 500 ns. The trip thresholds have a ? 95 mV, +45 mV
process and temperature variation.
Drivers
The NCP158x includes 0.7 A gate drivers to switch
external N ? channel MOSFETs. This allows the NCP158x to
address high ? power as well as low ? power conversion
requirements. The gate drivers also include adaptive
non ? overlap circuitry. The non ? overlap circuitry increase
efficiency, which minimizes power dissipation, by
minimizing the body diode conduction time.
A detailed block diagram of the non ? overlap and gate
drive circuitry used in the chip is shown in Figure 11.
http://onsemi.com
6
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1582DR2G | IC REG CTRLR BUCK PWM VM 8-SOIC |
| ASM12DSEH-S243 | CONN EDGECARD 24POS .156 EYELET |
| RCM31DCCT-S189 | CONN EDGECARD 62POS R/A .156 SLD |
| RCM31DCBT-S189 | CONN EDGECARD 62POS R/A .156 SLD |
| RCM31DCAT-S189 | CONN EDGECARD 62POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1583DR2GEVB | 功能描述:电源管理IC开发工具 ANA SWITCH REG EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1586DR2G | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| NCP1586DR2GH | 制造商:ON Semiconductor 功能描述: |
| NCP1587ADR2G | 功能描述:电压模式 PWM 控制器 BUCK CONTROLLER RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| NCP1587DR2G | 功能描述:电压模式 PWM 控制器 BUCK CONTROLLER RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。