参数资料
型号: NCP1654BP65G
厂商: ON Semiconductor
文件页数: 5/23页
文件大小: 228K
描述: IC PFC CCM STEP UP 8-PDIP
标准包装: 50
模式: 连续导电(CCM)
频率 - 开关: 58kHz ~ 72kHz
电流 - 启动: 75µA
电源电压: 9 V ~ 20 V
工作温度: -40°C ~ 125°C
安装类型: 通孔
封装/外壳: 8-DIP(0.300",7.62mm)
供应商设备封装: 8-PDIP
包装: 管件
其它名称: NCP1654BP65GOS
NCP1654
http://onsemi.com
5
DETAILED PIN DESCRIPTIONS
Pin
Symbol
Name
Function
1
GND
Ground

2
V
in
Multiplier
Voltage
This pin provides a voltage V
M
 for the PFC duty cycle modulation. The input impedance of the
PFC circuits is proportional to the resistor R
M
 externally connected to this pin. The device op-
erates in average current mode if an external capacitor C
M
 is connected to the pin. Otherwise,
it operates in peak current mode.
3
CS
Current Sense
Input
This pin sources a current I
CS
 which is proportional to the inductor current I
L
. The sense cur-
rent I
CS
 is for overcurrent protection (OCP), overpower limitation (OPL) and PFC duty cycle
modulation. When I
CS
 goes above 200 mA, OCP is activated and the Drive Output is disabled.
4
V
BO
BrownOut / In
Connect a resistor network among the rectified input voltage, BO pin, and ground. And connect
a capacitor between BO pin and ground. BO pin detects a voltage signal proportional to the
average input voltage.
When V
BO
 goes below V
BOL
, the circuit that detects too low input voltage conditions (brown
out), turns off the output driver and keeps it in low state until V
BO
 exceeds V
BOH
.
This signal which is proportional to the RMS input voltage V
ac
 is also for overpower limitation
(OPL) and PFC duty cycle modulation.
5
V
control
Control Voltage /
SoftStart
The voltage of this pin V
control
 directly controls the input impedance. This pin is connected to
external type2 compensation components to limit the V
control
 bandwidth typically below 20 Hz
to achieve near unity power factor.
The device provides no output when V
control
 < V
control(min)
. When it starts operation, the power
increases slowly (softstart).
6
V
FB
FeedBack /
Shutdown
This pin receives a feedback signal V
FB
 that is proportional to the PFC circuits output voltage.
This information is used for both the output regulation, the overvoltage protection (OVP), and
output undervoltage protection (UVP) to protect the system from damage at feedback abnor-
mal situation.
When V
FB
 goes above 105% V
REF
, OVP is activated and the Drive Output is disabled.
When V
FB
 goes below 8% V
REF
, the device enters a lowconsumption shutdown mode.
7
V
CC
Supply Voltage
This pin is the positive supply of the IC. The circuit typically starts to operate when V
CC
 ex-
ceeds 10.5 V and turns off when V
CC
 goes below 9 V. After startup, the operating range is 9 V
up to 20 V.
8
DRV
Drive Output
The high current capability of the totem pole gate drive (?.5 A) makes it suitable to effectively
drive high gate charge power MOSFET.
相关PDF资料
PDF描述
RAC05-05SA-E CONV AC/DC 90-264VAC 5V 1A
VE-J10-IZ CONVERTER MOD DC/DC 5V 25W
FAN6961DY IC PFC CONTROLLER DCM 8DIP
RAC10-3.3SA-E CONV AC/DC 90-264VAC 3.3V 3A
RBM08DRYS CONN EDGECARD 16POS DIP .156 SLD
相关代理商/技术参数
参数描述
NCP1654PFCGEVB 功能描述:电源管理IC开发工具 NCP1654 PWR FACT CONT EVB RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
NCP1729-SKT 制造商:P&S 功能描述:Sample Kit, including Two NCP1729SN35T1 and A Development Source CD-ROM 制造商:P&S 功能描述:Sample Kit,including Two NCP1729SN35T1 and A Development Source CD-ROM
NCP1729SN35T1 功能描述:电荷泵 Switched Cap Voltage RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube
NCP1729SN35T1G 功能描述:电荷泵 Switched Cap Voltage Inverter w/Shutdown RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube
NCP1729SN35T1G 制造商:ON Semiconductor 功能描述:Power Supply IC