参数资料
| 型号： | NCP2821FCT1G |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/19页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO D 2.65W 9-FLIPCHIP |
| 产品变化通告： | Product Discontinuation 09/Jan/2008 |
| 标准包装： | 3,000 |
| 类型： | D 类 |
| 输出类型： | 1-通道（单声道） |
| 在某负载时最大输出功率 x 通道数量： | 2.65W x 1 @ 4 欧姆 |
| 电源电压： | 2.2 V ~ 5.5 V |
| 特点： | 消除爆音，差分输入，关闭 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 9-覆晶 |
| 封装/外壳： | 9-WFBGA，FCBGA |
| 包装： | 带卷 (TR) |
NCP2821
http://onsemi.com
17
PCB Layout Information
NCP2821 is suitable for low cost solution. In a very small
package it gives all the advantages of a ClassD audio
amplifier. The required application board is focused on low
cost solution too. Due to its fully differential capability, the
audio signal can only be provided by an input resistor. If a
low pass filtering function is required, then an input
coupling capacitor is needed. The values of these
components determine the voltage gain and the bandwidth
frequency. The battery positive supply voltage requires a
good decoupling capacitor versus the expected distortion.
When the board is using Ground and Power planes with
at least 4 layers, a single 4.7
mF filtering ceramic capactior
on the bottom face will give optimized performance.
A 1.0
mF low ESR ceramic capacitor can also be used with
slightly degraded performances on the THD+N from 0.06%
up to 0.2%.
In a two layers application, if both Vp pins are connected
on the top layer, a single 4.7
mF decoupling capacitor will
optimize the THD+N level.
The NCP2821 power audio amplifier can operate from
2.5 V until 5.5 V power supply. With less than 2% THD+N,
it delivers 500 mW rms output power to a 8.0
W load at
Vp =3.0 V and 1.0 W rms output power at Vp = 4.0 V.
Figure 47. Top Layer
Note: This track between Vp pins is only needed when a 2 layers board is used. In case of a typical
4 or more layers, the use of laser vias in pad will optimize the THD+N floor. The demonstration
board delivered by ON Semiconductor is a 4 Layers with Top, Ground, Power Supply and Bottom.
Note
相关PDF资料 |
PDF描述 |
|---|---|
| NCP2824FCT2G | IC AMP MONO CLASS D AGC 9-WCSP |
| NCP2830MUTXG | IC AMP AUDIO CLASS D 20UQFN |
| NCP2890AFCT2 | IC AMP AUDIO POWER 1W 9-FLIPCHIP |
| NCP4894MNR2 | IC AMP AUDIO PWR 1W DIFF 10-DFN |
| NCP4896FCT1G | IC AMP AUDIO PORTABLE 9FLIPCHIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP2823 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High Efficiency 3W Filterless Class D Audio Amplifier |
| NCP2823AFCT2G | 功能描述:音频放大器 GRESHAM FCI AUDIO AMP RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| NCP2823AGEVB | 功能描述:音频 IC 开发工具 NCP2823A EVAL BOARD RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| NCP2823BFCT2G | 功能描述:音频放大器 GRESHAM FCI AUDIO AMP RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| NCP2823BGEVB | 功能描述:音频 IC 开发工具 NCP2823B EVB RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
发布紧急采购，3分钟左右您将得到回复。