- 您现在的位置：买卖IC网 > PDF目录17383 > NCP3127CRAGEVB (ON Semiconductor)BOARD EVALUATION NCP3127 CERAMIC PDF资料下载
参数资料
| 型号： | NCP3127CRAGEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION NCP3127 CERAMIC |
| 设计资源： | NCP3127 Schematic NCP3127 BOM |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 最低可调至 0.8V |
| 电流 - 输出： | 2A |
| 输入电压： | 4.5 ~ 13.2 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 350kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | NCP3127 |
| 其它名称： | NCP3127CRAGEVBOS |
NCP3127
General
The NCP3127 is a PWM synchronous buck regulator
COMP
intended to supply up to a 2 A load for DC ? DC conversion
from 5 V and 12 V buses. The NCP3127 is a regulator that
has integrated high ? side and low ? side NMOSFETs
switches. The output voltage of the converter can be
precisely regulated down to 800 mV $ 1.0% when the V FB
pin is tied to V OUT . The switching frequency is internally set
to 350 kHz. A high gain operational transconductance
amplifier (OTA) is used for voltage mode control of the
Gate Signal
Disable
Enable
2N7002E
power stage.
Duty Ratio and Maximum Pulse Width Limits
Disable
COMP
In steady state DC operation, the duty ratio will stabilize
at an operating point defined by the ratio of the input to the
output voltage. The device can achieve a 75% duty ratio. The
NCP3127 has a preset off ? time of approximately 150 ns,
which ensures that the bootstrap supply is charged every
switching cycle. The preset off time does not interfere with
Base Signal
Enable
MMBT3904
the conversion of 12 V to 0.8 V.
Input Voltage Range (V IN and BST)
The input voltage range for both V IN and BST is 4.5 V to
13.2 V with referenced to GND and V SW . Although BST is
rated at 13.2 V with respect to V SW , it can also tolerate
26.5 V with respect to GND.
External Enable/Disable
Once the input voltage has exceeded the boost and UVLO
Figure 16. Recommended Disable Circuits
Power Sequencing
Power sequencing can be achieved with NCP3127 using
two general purpose bipolar junction transistors or
MOSFETs. An example of the power sequencing circuit
using the external components is shown in Figure 17.
threshold at 3 V and V IN threshold at 4 V, the COMP pin
starts to rise. The V SW node is tri ? stated until the COMP
voltage exceeds 0.9 V. Once the 0.9 V threshold is exceeded,
the part starts to switch and the part is considered enabled.
When the COMP pin voltage is pulled below the 400 mV
VSW
NCP3127
FB1
COMP
1.0V
VIN
VSW
NCP3127
FB1
COMP
3.3 V
threshold, it disables the PWM logic, the top MOSFET is
driven off, and the bottom MOSFET is driven on. In the
disabled mode, the OTA output source current is reduced to
10 m A.
When disabling the NCP3127 using the COMP / Disable
pin, an open collector or open drain drive should be used as
shown in Figure 16:
0.9 V
COMP
BG
TG
Figure 15. Enable/Disable Driver State Diagram
Figure 17. Power Sequencing
Input Voltage Shutdown Behavior
Input voltage shutdown occurs when the IC stops
switching because the input supply reaches UVLO
threshold. Undervoltage Lockout (UVLO) is provided to
ensure that unexpected behavior does not occur when VCC
is too low to support the internal rails and power the
converter. For the NCP3127, the UVLO is set to permit
operation when converting from an input voltage of 5 V. If
the UVLO is tripped, switching stops, the internal SS is
discharged, and all MOSFET gates are driven low. The V SW
node enters a high impedance state and the output capacitors
discharge through the load with no ringing on the output
voltage.
External Soft ? Start
The NCP3127 features an external soft ? start function,
which reduces inrush current and overshoot of the output
voltage. Soft ? start is achieved by using the internal current
http://onsemi.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| NCP3125CRAGEVB | BOARD EVALUATION NCP3125 CERAMIC |
| R1S12-3.309-R | CONV DC/DC 1W 3.3VIN 09VOUT |
| RCC05DREI-S13 | CONN EDGECARD 10POS .100 EXTEND |
| 195D106X9016X2T | CAP TANT 10UF 16V 10% 2910 |
| GEC17DRTS-S93 | CONN EDGECARD 34POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP3155ADR2G | 功能描述:直流/直流开关调节器 BUCK CONTROLLER RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| NCP3155AGEVB | 功能描述:电源管理IC开发工具 BUCK CONTROLLER EVB RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP3155BDR2G | 功能描述:直流/直流开关调节器 3 A SYNCHRONOUS BUCK RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| NCP3155BGEVB | 功能描述:电源管理IC开发工具 3 A SYNCHRONOUS BUCK RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP3163_Boost_EVB | 制造商:ON Semiconductor 功能描述:3.4 A, Step-Up/Down/Inverting Switching Regulator 制造商:ON Semiconductor 功能描述:3.4A,24V,Step-Up Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。