- 您现在的位置：买卖IC网 > PDF目录13711 > NCP3163BMNR2G (ON Semiconductor)IC REG BUCK BOOST INV ADJ DFN18 PDF资料下载
参数资料
| 型号： | NCP3163BMNR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BOOST INV ADJ DFN18 |
| 标准包装： | 1 |
| 类型： | 降压（降压），升压（升压），反相 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 40V |
| 输入电压： | 2.5 V ~ 40 V |
| PWM 型： | 混合物 |
| 频率 - 开关： | 50kHz ~ 300kHz |
| 电流 - 输出： | 3.4A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 18-VFDFN 裸露焊盘 |
| 包装： | 剪切带 (CT) |
| 供应商设备封装： | 18-DFN（5x6） |
| 其它名称： | NCP3163BMNR2GOSCT |
NCP3163, NCV3163
INTRODUCTION
The NCP3163 is a monolithic power switching regulator
optimized for DC ? to ? DC converter applications. The
combination of its features enables the system designer to
directly implement step ? up, step ? down, and voltage ?
inverting converters with a minimum number of external
components. Potential applications include cost sensitive
consumer products as well as equipment for the automotive,
computer, and industrial markets. A representative block
diagram is shown in Figure 2.
OPERATING DESCRIPTION
The NCP3163 operates as a fixed on ? time, variable
off ? time voltage mode ripple regulator. In general, this
mode of operation is somewhat analogous to a capacitor
charge pump and does not require dominant pole loop
compensation for converter stability. The Typical Operating
Waveforms are shown in Figure 19. The output voltage
waveform shown is for a step ? down converter with the
ripple and phasing exaggerated for clarity. During initial
converter startup, the feedback comparator senses that the
output voltage level is below nominal. This causes the
output switch to turn on and off at a frequency and duty cycle
controlled by the oscillator, thus pumping up the output filter
capacitor. When the output voltage level reaches nominal,
the feedback comparator sets the latch, immediately
terminating switch conduction. The feedback comparator
will inhibit the switch until the load current causes the output
voltage to fall below nominal. Under these conditions,
output switch conduction can be inhibited for a partial
1
Comparator Output
0
1.25 V
Timing Capacitor C T
oscillator cycle, a partial cycle plus a complete cycle,
multiple cycles, or a partial cycle plus multiple cycles.
Oscillator
The oscillator frequency and on ? time of the output switch
are programmed by the value selected for timing capacitor
C T . Capacitor C T is charged and discharged by a 9 to 1 ratio
internal current source and sink, generating a negative going
sawtooth waveform at Pin 6. As C T charges, an internal
pulse is generated at the oscillator output. This pulse is
connected to the NOR gate center input, preventing output
switch conduction, and to the AND gate upper input,
allowing the latch to be reset if the comparator output is low.
Thus, the output switch is always disabled during ramp ? up
and can be enabled by the comparator output only at the start
of ramp ? down. The oscillator peak and valley thresholds are
1.25 V and 0.55 V, respectively, with a charge current of
225 m A and a discharge current of 25 m A, yielding a
maximum on ? time duty cycle of 90%. A reduction of the
maximum duty cycle may be required for specific converter
configurations. This can be accomplished with the addition
of an external deadtime resistor (R DT ) placed across C T . The
resistor increases the discharge current which reduces the
on ? time of the output switch. The converter output can be
inhibited by clamping C T to ground with an external NPN
small ? signal transistor. To calculate the frequency when
only C T is connected to Pin 6, use the equations found in
Figure 22. When R T is also used, the frequency and
maximum duty cycle can be calculated with the NCP3163
design tool found at www.onsemi.com.
0.55 V
1
Oscillator Output
0
On
Output Switch
Off
Nominal Output
Voltage Level
Output Voltage
t
Startup
9t
Quiescent Operation
Figure 19. Typical Operating Waveforms
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6726AKAVDD6+T | IC SUPERVISOR MPU SOT23-8 |
| VI-J4Z-CX | CONVERTER MOD DC/DC 2V 30W |
| SCB75F-3R3 | INDUCTOR SMD 3.3UH 2.16A 1KHZ |
| MAX6727AKALTD5+T | IC SUPERVISOR MPU SOT23-8 |
| VI-J4Y-CZ-S | CONVERTER MOD DC/DC 3.3V 16.5W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP3163BPWG | 功能描述:直流/直流开关调节器 ANA 2.5 A STEP UP/ DWN/INV RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| NCP3163BPWG | 制造商:ON Semiconductor 功能描述:Power Supply IC |
| NCP3163BPWR2G | 功能描述:直流/直流开关调节器 ANA 2.5 A STEP UP/ DWN/INV RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| NCP3163BSTEVB | 功能描述:电源管理IC开发工具 NCP3163 BOOST DEMO BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP3163BUCKEVB | 功能描述:BOARD EVAL NCP3163 BUCK RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
发布紧急采购，3分钟左右您将得到回复。