- 您现在的位置：买卖IC网 > PDF目录20650 > NCP5602MUTBG (ON Semiconductor)IC WHITE LED DVR HI EFF 12LLGA PDF资料下载
参数资料
| 型号： | NCP5602MUTBG |
| 厂商： | ON Semiconductor |
| 文件页数： | 3/12页 |
| 文件大小： | 0K |
| 描述： | IC WHITE LED DVR HI EFF 12LLGA |
| 产品变化通告： | Product Discontinuation 30/Sept/2011 |
| 标准包装： | 1 |
| 拓扑： | 切换式电容器（充电泵） |
| 输出数： | 2 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出电压： | 4.8 V ~ 5.7 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-UFLGA 裸露焊盘 |
| 供应商设备封装： | 12-LLGA（2x2） |
| 包装： | 剪切带 (CT) |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | NCP5602MUTBGOSCT |
NCP5602
PIN FUNCTION DESCRIPTION
Pin No.
1
Symbol
GND
Function
POWER
Description
This pin is the GROUND signal for the analog and digital blocks and must be
connected to the system ground. This pin is the GROUND reference for the
DC ? DC converter and the output current control. The pin must be connected
to the system ground, a ground plane being strongly recommended.
2
LED1
INPUT, POWER
This pin sinks to ground and monitors the current flowing into the first LED,
intended to be used in backlight application. The current is limited to 30 mA
maximum (see Note 2). When the ICON bit of the LED ? REG register is
High, the LED2 fulfills the ICON function. In this case, LED1 is deactivated.
3
LED2
INPUT, POWER
This pin sinks to ground and monitors the current flowing into the second
LED, intended to be used in backlight application. The current is limited to
30 mA maximum (see Note 2). When the ICON bit of the LED ? REG register
is High, the LED2 fulfills the ICON function. In this case, LED1 is
deactivated. The ICON current is 600 m A typical.
4
I REF
INPUT, ANALOG
This pin provides the reference current, based on the internal bandgap
voltage reference, to control the output current flowing in the LED. A 1%
tolerance, or better, resistor shall be used to get the highest accuracy of the
LED biases. An external current source can be used to bias this pin to dim
the light coming out of the LED.
In no case shall the voltage at pin 4 be forced either higher or lower than the
600 mV provided by the internal reference.
5
SDA
INPUT, DIGITAL
This pin carries the data provided by the I2C protocol. The content of the
SDA byte is used to program the mode of operation and to set up the output
current (see Table 2).
6
SCL
INPUT, DIGITAL
This pin carries the I2C clock to control the DC ? DC converter and to set up
the output current. The SCL clock is associated with the SDA signal.
7
VOUT
OUTPUT, POWER
This pin provides the output voltage supplied by the DC ? DC converter. The
Vout pin must be bypassed by 1.0 m F ceramic capacitor located as close as
possible to the pin to properly bypass the output voltage to ground. The
circuit shall not operate without such bypass capacitor properly connected to
the Vout pin.
The output voltage is internally clamped to 5.5 V maximum in the event of no
load situation. On the other hand, the output current is limited to 40 mA
(typical) in the event of a short circuit to ground.
8
9
10
11
C2P
C2N
C1P
VBAT
POWER
POWER
POWER
INPUT, POWER
One side of the external charge pump capacitor (C FLY ) is connected to this
pin, associated with C2N (see Note 1).
One side of the external charge pump capacitor (C FLY ) is connected to this
pin, associated with C2P (see Note 1).
One side of the external charge pump capacitor (C FLY ) is connected to this
pin, associated with C1N, pin 11 (see Note 1).
Input Battery voltage to supply the analog and digital blocks. The pin must be
decoupled to ground by a 1.0 m F ceramic capacitor.
12
C1N
POWER
One side of the external charge pump capacitor (C FLY ) is connected to this
pin, associated with C1P, pin 10 (see Note 1).
1. Using low ESR ceramic capacitor is mandatory to optimize the Charge Pump efficiency.
2. Total DC ? DC output current is limited to 60 mA.
http://onsemi.com
3
相关PDF资料 |
PDF描述 |
|---|---|
| C1005X7S2A472M | CAP CER 4700PF 100V 20% X7S 0402 |
| TC1313-VD0EMF | IC REG DL BUCK/LINEAR SYNC 10DFN |
| RMM44DRTI-S13 | CONN EDGECARD 88POS .156 EXTEND |
| TC1313-PP0EMFTR | IC REG DL BUCK/LINEAR SYNC 10DFN |
| ESM43DRAS | CONN EDGECARD 86POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP5603 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators |
| NCP5603GEVB | 功能描述:LED 照明开发工具 NCP5603 EVAL BRD RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| NCP5603MNR2 | 功能描述:LED照明驱动器 4.5V/5.0V Hi Eff. RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| NCP5603MNR2G | 功能描述:LED照明驱动器 4.5V/5.0V Hi Eff. White LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| NCP5603MNR2G-CUT TAPE | 制造商:ON 功能描述:NCP5603 Series 200 mA 5.5 V SMT High Efficiency Charge Pump Converter - DFN-10 |
发布紧急采购，3分钟左右您将得到回复。