参数资料
型号: NCP5602MUTBG
厂商: ON Semiconductor
文件页数: 6/12页
文件大小: 0K
描述: IC WHITE LED DVR HI EFF 12LLGA
产品变化通告: Product Discontinuation 30/Sept/2011
标准包装: 1
拓扑: 切换式电容器(充电泵)
输出数: 2
内部驱动器:
类型 - 主要: 背光,闪灯/白光
类型 - 次要: 白色 LED
频率: 1MHz
电源电压: 2.7 V ~ 5.5 V
输出电压: 4.8 V ~ 5.7 V
安装类型: 表面贴装
封装/外壳: 12-UFLGA 裸露焊盘
供应商设备封装: 12-LLGA(2x2)
包装: 剪切带 (CT)
工作温度: -40°C ~ 85°C
其它名称: NCP5602MUTBGOSCT
NCP5602
APPLICATION INFORMATION
DC ? DC Operation
The converter is based on a charge pump technique to
generate a DC voltage capable to supply the White LED
load. The system regulates the current flowing into each
LED by means of internal current mirrors associated with
the white diodes. Consequently, the output voltage will be
equal to the Vf of the LED, plus the drop voltage (ranging
from 200 mV to 400 mV, depending upon the output
current) developed across the internal NMOS mirror.
Typically, assuming a standard white LED forward biased
at 10 mA, the output voltage will be 3.8 V.
The built ? in OVP circuit continuously monitor each
output and stops the converter when the voltage is above
Rbias + 300 Iout (eq. 2)
Consequently, the resistor value will range between
R bias = 300/30 mA = 10 k W and R bias = 300/0.5 mA =
600 k W . Obviously, the tolerance of such a resistor must be
1% or better, with a 100 ppm thermal coefficient, to get the
expected overall tolerance.
VBandgap
5.0 V. The converter resumes to normal operation when the
voltage drops below 5.0 V (no latchup mechanism).
Consequently, the chip can operate with no load during any
test procedures.
Load Current Calculation
I REF
+
-
600mV
LED Return
Pin 2 & 3
The load current is derived from the 600 mV reference
voltage provided by the internal Bandgap associated to the
external resistor connected across I REF pin and Ground (see
Figure 3). In any case, no voltage shall be forced at I REF
pin, either downward or upward.
The reference current is multiplied by the constant
R1
GND
Pin 4
GND
Note: The I REF pin must never be
biased by an external voltage.
Figure 3. Basic Reference Current Source
Rbias + (Vref * k) Iout
k = 500 to yield the output load current. Since the reference
voltage is based on a temperature compensated Bandgap,
a tight tolerance resistor will provide a very accurate load
current. The resistor is calculated from the Ohm’s law
(R bias = Vref/I REF ) and a more practical equation can be
arranged to define the resistor value for a given output
current:
(eq. 1)
Rbias + (0.6 * 500) Iout
7
Load Connection
The NCP5602 chip is capable to drive the two LED
simultaneously, as depicted in Figure 1, but the load can be
arranged to accommodate one or two LED if necessary in
the application (see Figure 4). In this case, the two current
mirrors can be connected in parallel to drive a single power
full LED, thus yielding 60 mA current capability in a single
LED.
7
2
3
GND
2
3
GND
Figure 4. Typical Single and Double LED Connections
http://onsemi.com
6
相关PDF资料
PDF描述
C1005X7S2A472M CAP CER 4700PF 100V 20% X7S 0402
TC1313-VD0EMF IC REG DL BUCK/LINEAR SYNC 10DFN
RMM44DRTI-S13 CONN EDGECARD 88POS .156 EXTEND
TC1313-PP0EMFTR IC REG DL BUCK/LINEAR SYNC 10DFN
ESM43DRAS CONN EDGECARD 86POS R/A .156 SLD
相关代理商/技术参数
参数描述
NCP5603 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators
NCP5603GEVB 功能描述:LED 照明开发工具 NCP5603 EVAL BRD RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
NCP5603MNR2 功能描述:LED照明驱动器 4.5V/5.0V Hi Eff. RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5603MNR2G 功能描述:LED照明驱动器 4.5V/5.0V Hi Eff. White LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5603MNR2G-CUT TAPE 制造商:ON 功能描述:NCP5603 Series 200 mA 5.5 V SMT High Efficiency Charge Pump Converter - DFN-10