- 您现在的位置：买卖IC网 > PDF目录20815 > NCP5612MUTBG (ON Semiconductor)IC WHITE LED DRVR 12-LLGA PDF资料下载
参数资料
| 型号： | NCP5612MUTBG |
| 厂商： | ON Semiconductor |
| 文件页数： | 3/11页 |
| 文件大小： | 0K |
| 描述： | IC WHITE LED DRVR 12-LLGA |
| 标准包装： | 1 |
| 拓扑： | 切换式电容器（充电泵） |
| 输出数： | 2 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出电压： | 4.8 V ~ 5.7 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-UFLGA 裸露焊盘 |
| 供应商设备封装： | 12-LLGA（2x2） |
| 包装： | 剪切带 (CT) |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | NCP5612MUTBGOSCT |
NCP5612
PIN FUNCTION DESCRIPTION
Pin No.
1
Symbol
GND
Function
POWER
Description
This pin is the GROUND signal for the power analog blocks and must be
connected to the system ground. This pin is the GROUND reference for the
DC/DC converter and the output current control. The pin must be connected to
the system ground, a ground plane being strongly recommended.
2
LED1
INPUT, POWER
This pin sinks to ground and monitors the current flowing into the first LED,
intended to be used in backlight application. The current is limited to 30 mA
maximum (Note 2).
The LED1 is deactivated when the ICON bit of the LED?REG register is High.
The LED1 is automatically disconnected when an open load is sensed pin 2
during the operation.
3
LED2
INPUT, POWER
This pin sinks to ground and monitors the current flowing into the second LED,
intended to be used in backlight application. The current is limited to 30 mA
maximum (Note 2). The LED2 fulfills the ICON function, LED1 being
deactivated, when the ICON bit of the LED?REG register is High.
The LED2 is automatically disconnected when an open load is sensed pin 3
during the operation.
4
I REF
INPUT, ANALOG
This pin provides the reference current, based on the internal band?gap
voltage reference, to control the output current flowing in the LED. A 1%
tolerance, or better, resistor shall be used to get the highest accuracy of the
LED biases. An external current source can be used to bias this pin to dim the
light coming out of the LED.
In no case shall the voltage at pin 4 be forced either higher or lower than the
600 mV provided by the internal reference.
5
CNTL
INPUT, DIGITAL
This pin supports the flow of data between the external MCU and the
NCP5612 internal registers. The protocol makes profit of a Single Wire
structure associated to a Serial 8 bits format data flow.
6
7
NC
V OUT
?
OUTPUT, POWER
No internal connection
This pin provides the output voltage supplied by the DC/DC converter. The
V out pin must be decoupled to ground by a 1 m F ceramic capacitor located as
close as possible to the pin. Cares must be observed to minimize the parasitic
inductance at this pin. The circuit shall not operate without such bypass
capacitor connected across the V out pin and ground.
The output voltage is internally clamped to 5.5 V maximum in the event of no
load situation. On the other hand, the output current is limited to 40 mA
(typical) in the event of a short circuit to ground.
8
C2P
POWER
One side of the external charge pump capacitor (C FLY ) is connected to this
pin, associated with C2N (Note 1)
9
C2N
POWER
One side of the external charge pump capacitor (C FLY ) is connected to this
pin, associated with C2P (Note 1)
10
C1P
POWER
One side of the external charge pump capacitor (C FLY ) is connected to this
pin, associated with C1N (Note 1)
11
12
V BAT
C1N
INPUT, POWER
POWER
Input Battery voltage to supply the analog and digital blocks. The pin must be
decoupled to ground by a 1.0 m F minimum ceramic capacitor.
One side of the external charge pump capacitor (C FLY ) is connected to this
pin, associated with C1P (Note 1)
1. Using low ESR ceramic capacitor, 50 m W maximum, is mandatory to optimize the Charge Pump efficiency.
2. Total DC/DC output current is limited to 60 mA.
http://onsemi.com
3
相关PDF资料 |
PDF描述 |
|---|---|
| F971C106MBA | CAP TANT 10UF 16V 20% SMD |
| P51-3000-S-T-M12-4.5V-000-000 | SENSOR 3000PSI 7/16-20-2B 4.5V |
| REC3-2405DRW/H6/C/SMD-R | CONV DC/DC 3W 18-36VIN +/-05VOUT |
| REC8-1205DRW/H2/A/M/SMD-R | CONV DC/DC 8W 12VIN +/-05VOUT |
| P51-200-S-AA-P-5V-000-000 | SENSOR 200PSIS 7/16 UNF 5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP561SN15T1 | 功能描述:低压差稳压器 - LDO 1.5V 150mA CMOS RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP561SN15T1G | 功能描述:低压差稳压器 - LDO 1.5V 150mA CMOS w/Enable RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP561SN18T1 | 功能描述:低压差稳压器 - LDO 1.8V 150mA CMOS RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP561SN18T1G | 功能描述:低压差稳压器 - LDO 1.8V 150mA CMOS w/Enable RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP561SN25T1 | 功能描述:低压差稳压器 - LDO 2.5V 150mA CMOS RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。