- 您现在的位置：买卖IC网 > PDF目录20770 > NCP629FC33T2G (ON Semiconductor)IC REG LDO 3.3V .15A 5-FLIPCHIP PDF资料下载
参数资料
| 型号： | NCP629FC33T2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V .15A 5-FLIPCHIP |
| 产品变化通告： | Product Obsolescence 30/Sept/2009 |
| 标准包装： | 3,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 6V |
| 电压 - 压降（标准）： | 0.075V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA（最小值） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 5-UFBGA，FCBGA |
| 供应商设备封装： | 5-覆晶 |
| 包装： | 带卷 (TR) |
NCP629
DEFINITIONS
Load Regulation
The change in output voltage for a change in output load
current at a constant temperature.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 2% below its
nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Output Noise Voltage
This is the integrated value of the output noise over a
specified frequency range. Input voltage and output load
current are kept constant during the measurement. Results
are expressed in m V rms or nV/ √ Hz.
Disable and Ground Current
Ground Current (I GND ) is the current that flows through
the ground pin when the regulator operates with a load on its
output. This consists of internal IC operation, bias, etc. It is
actually the difference between the input current (measured
through the LDO input pin) and the output load current. If
the regulator has an input pin that reduces its internal bias
and shuts off the output (enable/disable function), this term
is called the disable current (I DIS .)
Line Regulation
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse techniques such that the
average junction temperature is not significantly affected.
Line Transient Response
Typical output voltage overshoot and undershoot
response when the input voltage is excited with a given
slope.
Load Transient Response
Typical output voltage overshoot and undershoot
response when the output current is excited with a given
slope between low-load and high-load conditions.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 175 ° C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Maximum Package Power Dissipation
The power dissipation level at which the junction
temperature reaches its maximum operating value.
APPLICATIONS INFORMATION
The NCP629 series regulator is self-protected with
internal thermal shutdown and internal current limit. Typical
application circuit is shown in Figure 1.
Input Decoupling (C in )
A ceramic or tantalum 1.0 m F capacitor is recommended
and should be connected close to the NCP629 package.
Higher capacitance and lower ESR will improve the overall
line transient response.
Output Decoupling (C out )
The NCP629 is a stable component and does not require
a minimum Equivalent Series Resistance (ESR) for the
output capacitor. The minimum output decoupling value is
1.0 m F and can be augmented to fulfill stringent load
transient requirements. The regulator works with ceramic
chip capacitors as well as tantalum devices. Typical
characteristics were measured with Murata ceramic
capacitors GRM31MR71E105KA01 (1.0 m F, 25 V X7R,
1206). Larger values improve noise rejection and load
regulation transient response. Figure 23 shows the stability
region for a range of operating conditions and ESR values.
No-Load Regulation Considerations
The NCP629 contains an overshoot clamp circuit to
improve transient response during a load current step
release. When output voltage exceeds the nominal by
approximately 20 mV, this circuit becomes active and
clamps the output from further voltage increase. Tying the
ENABLE pin to V in will ensure that the part is active
whenever the supply voltage is present, thus guaranteeing
that the clamp circuit is active whenever leakage current is
present.
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| NCP629FC30T2G | IC REG LDO 3V .15A 5-FLIPCHIP |
| ECA06DTBH | CONN EDGECARD 12POS R/A .125 SLD |
| NCP629FC28T2G | IC REG LDO 2.8V .15A 5-FLIPCHIP |
| NCP629FC18T2G | IC REG LDO 1.8V .15A 5-FLIPCHIP |
| NCP629FC15T2G | IC REG LDO 1.5V .15A 5-FLIPCHIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP629FC35T2G | 功能描述:低压差稳压器 - LDO HI PERFORMANCE CMOS RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP629FC50T2G | 功能描述:低压差稳压器 - LDO HI PERFORMANCE CMOS RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCP630 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:3.0 A Fast Linear Voltage Regulators |
| NCP630/D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:3.0 A Fast Linear Voltage Regulators |
| NCP630_05 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:3.0 A Fast Linear Voltage Regulators |
发布紧急采购，3分钟左右您将得到回复。