参数资料
型号: NCV2890DMR2G
厂商: ON Semiconductor
文件页数: 3/16页
文件大小: 0K
描述: IC PWR AMP AUDIO 1W 8-MICRO
标准包装: 4,000
类型: AB 类
输出类型: 1-通道(单声道)
在某负载时最大输出功率 x 通道数量: 1.08W x 1 @ 8 欧姆
电源电压: 2.2 V ~ 5.5 V
特点: 消除爆音,差分输入,短路和热保护,关闭
安装类型: 表面贴装
供应商设备封装: Micro8?
封装/外壳: 8-TSSOP,8-MSOP(0.118",3.00mm 宽)
包装: 带卷 (TR)
NCP2890, NCV2890
http://onsemi.com
11
APPLICATION INFORMATION
Detailed Description
The NCP2890 audio amplifier can operate under 2.6 V
until 5.5 V power supply. It delivers 320 mW rms output
power to 4.0
W load (Vp = 2.6 V) and 1.0 W rms output
power to 8.0
W load (Vp = 5.0 V).
The structure of the NCP2890 is basically composed of
two identical internal power amplifiers; the first one is
externally configurable with gainsetting resistors Rin and
Rf (the closedloop gain is fixed by the ratios of these
resistors) and the second is internally fixed in an inverting
unitygain configuration by two resistors of 20 k
W. So the
load is driven differentially through OUTA and OUTB
outputs. This configuration eliminates the need for an
output coupling capacitor.
Internal Power Amplifier
The output PMOS and NMOS transistors of the amplifier
were designed to deliver the output power of the
specifications without clipping. The channel resistance
(Ron) of the NMOS and PMOS transistors does not exceed
0.6
W when they drive current.
The structure of the internal power amplifier is
composed of three symmetrical gain stages, first and
medium gain stages are transconductance gain stages to
obtain maximum bandwidth and DC gain.
TurnOn and TurnOff Transitions
A cycle with a turnon and turnoff transition is
illustrated with plots that show both single ended signals on
the previous page.
In order to eliminate “pop and click” noises during
transitions, output power in the load must be slowly
established or cut. When logic high is applied to the
shutdown
pin, the bypass voltage begins to rise
exponentially and once the output DC level is around the
common mode voltage, the gain is established slowly
(50 ms). This way to turnon the device is optimized in
terms of rejection of “pop and click” noises.
The device has the same behavior when it is turnedoff
by a logic low on the shutdown pin. During the shutdown
mode, amplifier outputs are connected to the ground.
When a shutdown low level is applied, it takes 350 ms
before the DC output level is tied to Ground. However, as
shown on Figure 30, the turn off time of the audio signal is
40 ms.
A theoretical value of turnon time at 25
°C is given by
the following formula.
Cby: bypass capacitor
R: internal 300 k resistor with a 25% accuracy
Ton = 0.95 * R * Cby (285 ms with Cby = 1
mF)
If a faster turn on time is required then a lower bypass
capacitor can be used. The other option is to use NCP2892
which offers 100 ms with 1
mF bypass capacitor.
Shutdown Function
The device enters shutdown mode when shutdown signal
is low. During the shutdown mode, the DC quiescent
current of the circuit does not exceed 100 nA.
Current Limit Circuit
The maximum output power of the circuit (Porms =
1.0 W, Vp = 5.0 V, RL = 8.0
W) requires a peak current in
the load of 500 mA.
In order to limit the excessive power dissipation in the
load when a shortcircuit occurs, the current limit in the
load is fixed to 800 mA. The current in the four output MOS
transistors are realtime controlled, and when one current
exceeds 800 mA, the gate voltage of the MOS transistor is
clipped and no more current can be delivered.
Thermal Overload Protection
Internal
amplifiers
are
switched
off
when
the
temperature exceeds 160
°C, and will be switched on again
only when the temperature decreases fewer than 140
°C.
The NCP2890 is unitygain stable and requires no
external components besides gainsetting resistors, an
input coupling capacitor and a proper bypassing capacitor
in the typical application.
The first amplifier is externally configurable (Rf and
Rin), while the second is fixed in an inverting unity gain
configuration.
The differentialended amplifier presents two major
advantages:
The possible output power is four times larger (the
output swing is doubled) as compared to a singleended
amplifier under the same conditions.
Output pins (OUTA and OUTB) are biased at the same
potential Vp/2, this eliminates the need for an output
coupling
capacitor required with a singleended
amplifier configuration.
The differential closed loopgain of the amplifier is
given by Avd + 2*
Rf
Rin
+
Vorms
Vinrms
.
Output power delivered to the load is given by
Porms +
(Vopeak)2
2* RL
(Vopeak is the peak differential
output voltage).
When choosing gain configuration to obtain the desired
output power, check that the amplifier is not current limited
or clipped.
The maximum current which can be delivered to the load
is 500 mA Iopeak +
Vopeak
RL
.
相关PDF资料
PDF描述
MS27468E15F18P CONN RCPT 18POS JAM NUT W/PINS
MS27484T16A26SLC CONN HSG PLUG 26POS STRGHT SCKT
MS27508E14F18SA CONN RCPT 18POS BOX MNT W/SCKT
D38999/20WD15SNLC CONN HSG RCPT 15POS WALL MT SCKT
MS27468T17F99P CONN RCPT 23POS JAM NUT W/PINS
相关代理商/技术参数
参数描述
NCV2901 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Single Supply Quad Comparators
NCV2901CTR 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Single Supply Quad Comparators
NCV2901DR2 功能描述:校验器 IC 3-36V Qud Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压(最大值):6 mV 电源电流(最大值):1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel
NCV2901DR2G 功能描述:校验器 IC 3-36V Qud Comparator Commercial Temp RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压(最大值):6 mV 电源电流(最大值):1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel
NCV2901DTBR2G 功能描述:校验器 IC ANA SGL SUP CMP QUAD RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压(最大值):6 mV 电源电流(最大值):1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel