- 您现在的位置：买卖IC网 > PDF目录20041 > NCV4299D1R2G (ON Semiconductor)IC REG LDO 5V .15A 8-SOIC PDF资料下载
参数资料
| 型号： | NCV4299D1R2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 16/23页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V .15A 8-SOIC |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 5V |
| 输入电压： | 最高 45 V |
| 电压 - 压降（标准）： | 0.22V @ 100mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 电流 - 限制（最小）： | 250mA |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 剪切带 (CT) |
| 其它名称： | NCV4299D1R2GOSCT |
NCV4299
Reset Output (RO)
A reset signal, Reset Output (RO, low voltage) is
generated as the IC powers up. After the output voltage V Q
increases above the reset threshold voltage V RT , the delay
timer D is started. When the voltage on the delay timer V D
passes V UD , the reset signal RO goes high. A discharge of
the delay timer (V D ) is started when V Q drops and stays
below the reset threshold voltage V RT . When the voltage of
the delay timer (V D ) drops below the lower threshold
voltage V LD , the reset output voltage V RO is brought low to
reset the processor.
The reset output RO is an open collector NPN transistor,
controlled by a low voltage detection circuit. The circuit is
functionally independent of the rest of the IC, thereby
guaranteeing that RO is valid for V Q as low as 1.0 V.
V I
t
V Q
< t RR
V RT
t
+ D
V D
V UD
V LD
V RO
V RO,SAT
t d
t RR
dV
dt
I
CD
t
t
Power ? on ? Reset
Thermal
Shutdown
Voltage Dip
at Input
Undervoltage
Secondary
Spike
Overload
at Output
Figure 41. Reset Timing Diagram
Reset Adjust (RADJ)
The reset threshold V RT can be decreased from a typical
value of 4.64 V to as low as 3.5 V by using an external
voltage divider connected from the Q lead to the pin RADJ,
as shown in Figures 39 and 40. The resistor divider keeps the
voltage above the V RADJ,TH , (typ. 1.36 V), for the desired
input voltages and overrides the internal threshold detector.
Adjust the voltage divider according to the following
relationship:
VTHRES + VRADJ, TH · (RADJ1 ) RADJ2) RADJ2
(eq. 1)
If the reset adjust option is not needed, the RADJ ? pin
should be connected to GND causing the reset threshold to
Reset Delay (D)
The reset delay circuit provides a delay (programmable by
capacitor C D ) on the reset output RO lead. The delay lead D
provides charge current I D (typically 7.1 m A) to the external
delay capacitor C D during the following times:
1. During Powerup (once the regulation threshold has
been exceeded).
2. After a reset event has occurred and the device
is back in regulation. The delay capacitor is
set to discharge when the regulation (V RT , reset
threshold voltage) has been violated. When
the delay capacitor discharges to down to V LD ,
the reset signal RO pulls low.
go to its default value (typ. 4.64 V).
http://onsemi.com
16
相关PDF资料 |
PDF描述 |
|---|---|
| VE-201-CX | CONVERTER MOD DC/DC 12V 75W |
| MENB1090A1503F01 | POWER SUPPLY SWITCHER 90W 15V |
| LTC1422IS8#PBF | IC CONTROLLER HOT SWAP 8-SOIC |
| NCP694HSANADJT1G | IC REG LDO ADJ 1A 6HSON |
| EMA49DRMN-S288 | CONN EDGECARD 98POS .125 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV4299D2 | 功能描述:低压差稳压器 - LDO 5V 150mA Precision RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV4299D233G | 功能描述:低压差稳压器 - LDO ANA 150mA LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV4299D233R2G | 功能描述:低压差稳压器 - LDO ANA 150mA LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV4299D2G | 功能描述:低压差稳压器 - LDO LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV4299D2R2 | 功能描述:低压差稳压器 - LDO 5V 150mA Precision RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。