- 您现在的位置：买卖IC网 > PDF目录20041 > NCV4299D1R2G (ON Semiconductor)IC REG LDO 5V .15A 8-SOIC PDF资料下载
参数资料
| 型号： | NCV4299D1R2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 17/23页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V .15A 8-SOIC |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 5V |
| 输入电压： | 最高 45 V |
| 电压 - 压降（标准）： | 0.22V @ 100mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 电流 - 限制（最小）： | 250mA |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 剪切带 (CT) |
| 其它名称： | NCV4299D1R2GOSCT |
NCV4299
td + [CD (VUD ? VD, sat)] ID
td + [100 nF(1.85 ? 0.1 V)] 7.1 m A + 24.6 ms
Setting the Delay Time
The delay time is set by the delay capacitor C D and the
charge current I D . The time is measured by the delay
capacitor voltage charging from the low level of V D,sat to the
higher level V UD . The time delay follows the equation:
(eq. 2)
Example:
Using C D = 100 nF.
Use the typical value for V D,sat = 0.1 V.
Use the typical value for V UD = 1.85 V.
Use the typical value for Delay Charge Current I D = 7.1 m A.
(eq. 3)
When the output voltage V Q drops below the reset
threshold voltage V RT , the voltage on the delay capacitor V D
starts to drop. The time it takes to drop below the lower
threshold voltage of V LD is the reset reaction time, t RR . This
time is typically 2.2 m s for a delay capacitor of 0.1 m F. The
reset reaction time can be estimated from the following
relationship:
Sense Input (SI)/Sense Output (SO) Voltage Monitor
An on ? chip comparator is available to provide early
warning to the microprocessor of a possible reset signal. The
reset signal typically turns the microprocessor off
instantaneously. This can cause unpredictable results with
the microprocessor. The signal received from the SO pin will
allow the microprocessor time to complete its present task
before shutting down. This function is performed by a
comparator referenced to the band gap voltage. The actual
trip point can be programmed externally using a resistor
divider to the input monitor (SI) (Figures 39 and 40). The
typical threshold is 1.35 V on the SI Pin.
Signal Output
Figure 42 shows the SO Monitor waveforms as a result of
the circuits depicted in Figures 39 and 40. As the output
voltage V Q falls, the monitor threshold V SI,Low is crossed.
This causes the voltage on the SO output to go low sending
a warning signal to the microprocessor that a reset signal may
occur in a short period of time. T WARNING is the time the
microprocessor has to complete the function it is currently
tRR + 22 ns nF
CD
(eq. 4)
working on and get ready for the reset shutdown signal.
Sense
Input
Voltage
V Q
V SI
V SI,Low
V SI,High
V SI,Low
V RO
Sense
Output
t PSOLH
t
t PSOHL
High
V SO
T WARNING
Low
t
R q JA + (150 ° C ? TA) PD
Figure 42. SO Warning Timing Waveform
Calculating Power Dissipation in a Single Output
Linear Regulator
The maximum power dissipation for a single output
regulator is:
PD(max) + [VI(max) ? VQ(min)] IQ(max) ) VI(max)Iq
(eq. 5)
where:
V I(max) is the maximum input voltage,
V Q(min) is the minimum output voltage,
I Q(max) is the maximum output current for the application,
and
Figure 43. Sense Timing Diagram
I q is the quiescent current the regulator consumes at I Q(max) .
Once the value of P D(max) is known, the maximum
permissible value of R q JA can be calculated:
(eq. 6)
The value of R q JA can then be compared with those in the
package section of the data sheet. Those packages with
R q JA ’s less than the calculated value in Equation 6 will keep
the die temperature below 150 ° C. In some cases, none of the
packages will be sufficient to dissipate the heat generated by
the IC, and an external heatsink will be required.
http://onsemi.com
17
相关PDF资料 |
PDF描述 |
|---|---|
| VE-201-CX | CONVERTER MOD DC/DC 12V 75W |
| MENB1090A1503F01 | POWER SUPPLY SWITCHER 90W 15V |
| LTC1422IS8#PBF | IC CONTROLLER HOT SWAP 8-SOIC |
| NCP694HSANADJT1G | IC REG LDO ADJ 1A 6HSON |
| EMA49DRMN-S288 | CONN EDGECARD 98POS .125 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV4299D2 | 功能描述:低压差稳压器 - LDO 5V 150mA Precision RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV4299D233G | 功能描述:低压差稳压器 - LDO ANA 150mA LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV4299D233R2G | 功能描述:低压差稳压器 - LDO ANA 150mA LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV4299D2G | 功能描述:低压差稳压器 - LDO LDO REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV4299D2R2 | 功能描述:低压差稳压器 - LDO 5V 150mA Precision RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。