- 您现在的位置：买卖IC网 > PDF目录13680 > NCV51411DR2G (ON Semiconductor)IC REG BUCK 1.5A 8SOIC PDF资料下载
参数资料
| 型号： | NCV51411DR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 1.5A 8SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出数： | 1 |
| 输入电压： | 4.5 V ~ 40 V |
| PWM 型： | 混合物 |
| 频率 - 开关： | 260kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 剪切带 (CT) |
| 供应商设备封装： | 8-SOICN |
| 其它名称： | NCV51411DR2GOSCT |
NCV51411
WBASE + O
V 2
VIN
IS
60
where:
I S = DC switching current.
When the power switch turns on, the saturation voltage
and conduction current contribute to the power loss of a
non ? ideal switch. The power loss can be quantified as
WSAT +
VO
VIN
IS
VSAT
where:
V SAT = saturation voltage of the power switch which is
shown in Figure 5.
WS + S
30 ns
fS
The switching loss occurs when the switch experiences
both high current and voltage during each switch transition.
This regulator has a 30 ns turn ? off time and associated
power loss is equal to
I VIN
2
The turn ? on time is much shorter and thus turn ? on loss is
not considered here.
The total power dissipated by the IC is sum of all the above
WIC + WQ ) WDRV ) WBASE ) WSAT ) WS
The IC junction temperature can be calculated from the
ambient temperature, IC power dissipation and thermal
resistance of the package. The equation is shown as follows,
TJ + WIC R q JA ) TA
Minimum Load Requirement
As pointed out in the previous section, a minimum load is
required for this regulator due to the pre ? driver current
feeding the output. Placing a resistor equal to V O divided by
12 mA should prevent any voltage overshoot at light load
Figure 11. Input Voltage Ripple in a Buck Converter
To calculate the RMS current, multiply the load current
with the constant given by Figure 12 at each duty cycle. It is
a common practice to select the input capacitor with an RMS
current rating more than half the maximum load current. If
multiple capacitors are paralleled, the RMS current for each
capacitor should be the total current divided by the number
of capacitors.
0.6
0.5
0.4
0.3
0.2
0.1
conditions. Alternatively, the feedback resistors can be
valued properly to consume 12 mA current.
0
0
0.2
0.4
0.6
0.8
1.0
DUTY CYCLE
COMPONENT SELECTION
Input Capacitor
In a buck converter, the input capacitor witnesses pulsed
current with an amplitude equal to the load current. This
pulsed current and the ESR of the input capacitors determine
the V IN ripple voltage, which is shown in Figure 11. For V IN
ripple, low ESR is a critical requirement for the input
capacitor selection. The pulsed input current possesses a
significant AC component, which is absorbed by the input
capacitors. The RMS current of the input capacitor can be
calculated using:
Figure 12. Input Capacitor RMS Current can be
Calculated by Multiplying Y Value with Maximum Load
Current at any Duty Cycle
Selecting the capacitor type is determined by each
design’s constraint and emphasis. The aluminum
electrolytic capacitors are widely available at lowest cost.
Their ESR and ESL (equivalent series inductor) are
relatively high. Multiple capacitors are usually paralleled to
achieve lower ESR. In addition, electrolytic capacitors
usually need to be paralleled with a ceramic capacitor for
filtering high frequency noises. The OS ? CON are solid
aluminum electrolytic capacitors, and therefore has a much
where:
IRMS + IO D(1 * D)
lower ESR. Recently, the price of the OS ? CON capacitors
has dropped significantly so that it is now feasible to use
D = switching duty cycle which is equal to V O /V IN .
I O = load current.
them for some low cost designs. Electrolytic capacitors are
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| GBC49DRYH-S13 | CONN EDGECARD 98POS .100 EXTEND |
| GCC31DRTF-S13 | CONN EDGECARD 62POS .100 EXTEND |
| SC1704-100 | INDUCTOR SMD 10UH 0.50A 100KHZ |
| NCV5171EDR2G | IC REG MULTI CONFIG 1.5A 8SOIC |
| UPM2A150MED1TD | CAP ALUM 15UF 100V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV51411MNR2 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.5 A, 260 kHz, Low Voltage Buck Regulator with Synchronization Capability |
| NCV51411MNR2G | 功能描述:直流/直流开关转换器 BUCK REGULATOR RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCV51411PWR2 | 功能描述:直流/直流开关转换器 1.5A Low Voltage RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCV51411PWR2G | 功能描述:直流/直流开关转换器 1.5A Low Voltage Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| NCV5171 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.5 A 280 kHz Boost Regulators |
发布紧急采购，3分钟左右您将得到回复。