参数资料
| 型号： | NCV73810V2GEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 3/19页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FLEXRAY BUS NCV7381 |
| 设计资源： | NCV73810V2GEVB BOM NCV73810V2GEVB Gerber Files NCV73810V2GEVB Schematic |
| 标准包装： | 1 |
| 系列： | FlexRay™ |
| 主要目的： | 接口，Flexray |
| 嵌入式： | 是，MCU，16 位 |
| 已用 IC / 零件： | NCV7381 |
| 主要属性： | 2 通道 |
| 次要属性： | LED 状态指示器 |
| 已供物品： | 板 |
| 其它名称： | NCV73810V2GEVBOS |
NCV73810V2GEVB
GETTING STARTED
The NCV7381EVB board is fully assembled, pre-programmed and can be immediately used for evaluation. Only a few steps
need be proceeded to get fully working simple FlexRay network.
Connect the evaluation boards as follows:
1. Set the boards to default configuration according to Jumpers and Default Configuration section
2. Set a different board address on each board. One of the boards must be set with address 1 and is considered as Master
Board. Node address is configurable by address switch (SW12) – see Address Switch section for details
3. Connect the boards according to figure below
4. Optionally connect an oscilloscope to any test-point as needed
5. After the power supply is applied, FlexRay communication is automatically initialized
With properly running setup, button SW11 (#IRQ) has following functions:
? Press the button shortly to read-out Bus Driver status register (Only in Bus Driver status indication mode)
? Press and hold the button for approximately 2 seconds to change LED bar indication mode. Three modes are available:
?
?
?
?
FlexRay communication indication – each LED is assigned to one slot according to LED number. The LED is blinking
if the respective slot in FlexRay communication is active
Bus Driver status indication – Channel A,
Bus Driver status indication – Channel B:
LED1 – Local Wake-Up status
LED2 – Remote Wake-Up status
LED3 – TxEN-BGE Timeout status
LED4 – Bus Error status
LED5 – Vio Undervoltage status
LED6 – Vcc Undervoltage status
LED7 – Vbat Undervoltage status
LED8 – Power On status
Press and hold the button for more than 5 seconds – Both nodes are switched to SLEEP mode and can be woken-up by
one of the Local Wake-up switches. Only Node 1 is allowed to send the rest of network to SLEEP mode
In SLEEP mode, NCV7381 is supplied only from VBAT supply. VCC and VIO power supplies are switched off by NCV7381
INH output. MCU is not running and the board can be woken-up only with one of the Local Wakeup buttons (SW70, SW80).
? NCV7381 Local Wakeup function – Wake-up one of the nodes by any Local Wakeup button
? NCV7381 Remote Wakeup function – Second node is woken-up by Remote Wakeup pattern sent over the FlexRay bus
by first node during initialization phase after Local Wakeup
http://onsemi.com
3
相关PDF资料 |
PDF描述 |
|---|---|
| NF20AA0509MHL | CURRENT LIMITER INRUSH 5OHM 20% |
| NHD-4.3-480272MF-20 | BOARD CTRLR FOR NHDEV 4.3 TFT |
| NHDEV DEVELOPMENT BOARD | BOARD DEV LCD COG TFT 100X95MM |
| NP0120TAT1G | IC PROTECTOR LOW CAP 12V 5TSOP |
| NP1500SCT3G | THYRISTOR TSPD 100A 150V SMB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV7381DP0G | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:FlexRay Bus Driver |
| NCV7381DP0R2G | 功能描述:总线收发器 CLAMP 30 FLEXRAY TRANSC. RoHS:否 制造商:Fairchild Semiconductor 逻辑类型:CMOS 逻辑系列:74VCX 每芯片的通道数量:16 输入电平:CMOS 输出电平:CMOS 输出类型:3-State 高电平输出电流:- 24 mA 低电平输出电流:24 mA 传播延迟时间:6.2 ns 电源电压-最大:2.7 V, 3.6 V 电源电压-最小:1.65 V, 2.3 V 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-48 封装:Reel |
| NCV7382 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Enhanced LIN Transceiver |
| NCV7382/D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Enhanced LIN Transceiver |
| NCV7382_07 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Enhanced LIN Transceiver |
发布紧急采购，3分钟左右您将得到回复。