参数资料
| 型号： | NCV73810V2GEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/19页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FLEXRAY BUS NCV7381 |
| 设计资源： | NCV73810V2GEVB BOM NCV73810V2GEVB Gerber Files NCV73810V2GEVB Schematic |
| 标准包装： | 1 |
| 系列： | FlexRay™ |
| 主要目的： | 接口，Flexray |
| 嵌入式： | 是，MCU，16 位 |
| 已用 IC / 零件： | NCV7381 |
| 主要属性： | 2 通道 |
| 次要属性： | LED 状态指示器 |
| 已供物品： | 板 |
| 其它名称： | NCV73810V2GEVBOS |
NCV73810V2GEVB
Address Switch
This switch is used for setting a node number. Each board is programmed with the same firmware, so every node in the
network must be configured with different unique number.
Be careful:
LSB is situated on the left.
ON means the particular switch is closed and output is
Logical 0 !
OFF means the particular switch is open and output is
Logical 1 !
0 1 2 3 4 5 6 7
OFF
ON
MCU Reset Button
This switch is used for generating low level at the MCU Reset pin. If MCU detects low level at the RESET pin external reset
is performed.
MCU External Interrupt Button
The MCU interrupt module support one maskable interrupt input. This input is connected to SW11.
BD Local Wakeup Buttons
The FlexRay Bus drivers support Local Wakeup event detection. If a falling edge is recognized on WAKE pin, a local wakeup
is detected. These switches (each for one FlexRay channel) are used for simulation of Local wakeup event normally generated
by e.g. mechanical switch.
LEDs
Three power LEDs indicate proper function of voltage regulators. In case the MCU and the NCV7381 bus drivers IO cells
use the same power supply (as by default) MCU VCC LED and BD VIO LED signalling is also the same.
The board contains a bank of eight general purpose LEDs (Green). Their function depends on the MCU program. There is
also USB indication LED which is used to signal ongoing USB data transmission.
Figure 3. LEDs Description
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| NF20AA0509MHL | CURRENT LIMITER INRUSH 5OHM 20% |
| NHD-4.3-480272MF-20 | BOARD CTRLR FOR NHDEV 4.3 TFT |
| NHDEV DEVELOPMENT BOARD | BOARD DEV LCD COG TFT 100X95MM |
| NP0120TAT1G | IC PROTECTOR LOW CAP 12V 5TSOP |
| NP1500SCT3G | THYRISTOR TSPD 100A 150V SMB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV7381DP0G | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:FlexRay Bus Driver |
| NCV7381DP0R2G | 功能描述:总线收发器 CLAMP 30 FLEXRAY TRANSC. RoHS:否 制造商:Fairchild Semiconductor 逻辑类型:CMOS 逻辑系列:74VCX 每芯片的通道数量:16 输入电平:CMOS 输出电平:CMOS 输出类型:3-State 高电平输出电流:- 24 mA 低电平输出电流:24 mA 传播延迟时间:6.2 ns 电源电压-最大:2.7 V, 3.6 V 电源电压-最小:1.65 V, 2.3 V 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-48 封装:Reel |
| NCV7382 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Enhanced LIN Transceiver |
| NCV7382/D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Enhanced LIN Transceiver |
| NCV7382_07 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Enhanced LIN Transceiver |
发布紧急采购，3分钟左右您将得到回复。