参数资料
| 型号： | NUD3105DMT1 |
| 厂商： | ON Semiconductor |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC INDCT LOAD DRVR DUAL SC74-6 |
| 标准包装： | 1 |
| 类型： | 低端 |
| 输入类型： | 非反相 |
| 输出数： | 2 |
| 导通状态电阻： | 1.2 欧姆 |
| 电流 - 输出 / 通道： | 400mA |
| 电流 - 峰值输出： | 500mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74，SOT-457 |
| 供应商设备封装： | SC-74 |
| 包装： | 剪切带 (CT) |
| 其它名称： | NUD3105DMT1OSCT |
NUD3105D
Designing with this Data Sheet
1. Determine the maximum inductive load current (at
max V CC , min coil resistance & usually minimum
temperature) that the NUD3105D will have to
drive and make sure it is less than the max rated
current.
2. For pulsed operation, use the Transient Thermal
Response of Figure 11 and the instructions with it
to determine the maximum limit on transistor
power dissipation for the desired duty cycle and
temperature range.
3. Use Figures 10 and 11 with the SOA notes to
insure that instantaneous operation does not push
the device beyond the limits of the SOA plot.
4. Verify that the circuit driving the gate will meet
the V GS(th) from the Electrical Characteristics
table.
5. Using the max output current calculated in step 1,
check Figure 7 to insure that the range of Zener
clamp voltage over temperature will satisfy all
system & EMI requirements.
6. Use I GSS and I DSS from the Electrical
Characteristics table to insure that “OFF” state
leakage over temperature and voltage extremes
does not violate any system requirements.
7. Review circuit operation and insure none of the
device max ratings are being exceeded.
APPLICATIONS DIAGRAMS
+3.0 ≤ V DD ≤ +3.75 Vdc
+4.5 ≤ V CC ≤ +5.5 Vdc
V out (6)
+
+
V out (3)
NUD3105DDMT1
V in (2)
GND (1)
GND (4)
V in (5)
Figure 12. A 200 mW, 5.0 V Dual Coil Latching Relay Application
with 3.0 V Level Translating Interface
http://onsemi.com
6
相关PDF资料 |
PDF描述 |
|---|---|
| NUD3105LT1 | IC INDCT LOAD/RELAY DRVR SOT23 |
| NUD3112LT1 | IC INDCT LOAD/RELAY DRVR SOT23 |
| NUD3124LT1 | IC INDCT LOAD DRVR AUTO SOT23 |
| NUD3160LT1 | IC INDCT LOAD DRVR INDUST SOT23 |
| NUS3116MTR2G | IC MOSFET MAIN SW DUAL BJT 8-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NUD3105DMT1G | 功能描述:MOSFET 5V Dual Integrated Relay Inductive Load RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube |
| NUD3105DMT1G-CUT TAPE | 制造商:ON 功能描述:NUD Series 6 V 500 mA SMT Integrated Relay Inductive Load Driver - SC-74 |
| NUD3105LT1 | 功能描述:MOSFET 8V Inductive Load RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube |
| NUD3105LT1G | 功能描述:MOSFET 8V Inductive Load RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube |
| NUD3112 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Integrated Relay, Inductive Load Driver |
发布紧急采购，3分钟左右您将得到回复。