- 您现在的位置：买卖IC网 > PDF目录19410 > NVT210CMTR2G (ON Semiconductor)IC TEMP SENSOR DGTL 8-WDFN PDF资料下载
参数资料
| 型号： | NVT210CMTR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 17/20页 |
| 文件大小： | 325K |
| 描述： | IC TEMP SENSOR DGTL 8-WDFN |
| 标准包装： | 3,000 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 127°C，-64°C ~ 191°C |
| 精确度： | ±2.5°C |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | 2 线串行，I²C?/SMBUS? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 2.8 V ~ 3.6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN |
| 供应商设备封装： | 8-WDFN（2x2） |
| 包装： | 带卷 (TR) |
NVT210
http://onsemi.com
17
causes a lag in the response of the sensor to a temperature
change. In the case of the remote sensor, this should not be
a problem since it is either a substrate transistor in the
processor or a small package device, such as the SOT23,
placed in close proximity to it.
The on-chip sensor, however, is often remote from the
processor and only monitors the general ambient
temperature around the package. How accurately the
temperature of the board and/or the forced airflow reflects
the temperature to be measured dictates the accuracy of the
measurement. Self-heating due to the power dissipated in
the NVT210 or the remote sensor causes the chip
temperature of the device or remote sensor to rise above
ambient. However, the current forced through the remote
sensor is so small that self-heating is negligible. In the case
of the NVT210, the worst-case condition occurs when the
device is converting at 64 conversions per second while
sinking the maximum current of 1 mA at the ALERT
and
THERM
output. In this case, the total power dissipation in
the device is about 4.5 mW. The thermal resistance, q
JA
, of
the 8-lead DFN is approximately 142癈/W.
Layout Considerations
Digital boards can be electrically noisy environments, and
the NVT210 is measuring very small voltages from the
remote sensor, so care must be taken to minimize noise
induced at the sensor inputs. Take the following precautions:
?SPAN class="pst NVT210DMTR2G_2295433_3"> Place the NVT210 as close as possible to the remote
sensing diode. Provided that the worst noise sources,
that is, clock generators and data/address buses are
avoided, this distance can be 4 inches to 8 inches.
?SPAN class="pst NVT210DMTR2G_2295433_3"> Route the D+ and D tracks close together, in parallel,
with grounded guard tracks on each side. To minimize
inductance and reduce noise pickup, a 5 mil track width
and spacing is recommended. Provide a ground plane
under the tracks, if possible.
Figure 22. Typical Arrangement of Signal Tracks
5 MIL
5 MIL
5 MIL
5 MIL
5 MIL
5 MIL
5 MIL
GND
D
D+
GND
?SPAN class="pst NVT210DMTR2G_2295433_3"> Try to minimize the number of copper/solder joints that
can cause thermocouple effects. Where copper/solder
joints are used, make sure that they are in both the D+
and D path and at the same temperature.
?SPAN class="pst NVT210DMTR2G_2295433_3"> Thermocouple effects should not be a major problem as
1癈 corresponds to about 200 mV, and thermocouple
voltages are about 3 mV/癈 of temperature difference.
Unless there are two thermocouples with a big
temperature differential between them, thermocouple
voltages should be much less than 200 mV.
?SPAN class="pst NVT210DMTR2G_2295433_3"> Place a 0.1 mF bypass capacitor close to the V
DD
pin. In
extremely noisy environments, place an input filter
capacitor across D+ and D close to the NVT210. This
capacitance can effect the temperature measurement, so
ensure that any capacitance seen at D+ and D is, at
maximum, 1,000 pF. This maximum value includes the
filter capacitance, plus any cable or stray capacitance
between the pins and the sensor diode.
?SPAN class="pst NVT210DMTR2G_2295433_3"> If the distance to the remote sensor is more than
8 inches, the use of twisted pair cable is recommended.
A total of 6 feet to 12 feet is needed.
For really long distances (up to 100 feet), use a shielded
twisted pair, such as the Belden No. 8451 microphone
cable. Connect the twisted pair to D+ and D and the
shield to GND close to the NVT210. Leave the remote
end of the shield unconnected to avoid ground loops.
Because the measurement technique uses switched
current sources, excessive cable or filter capacitance can
affect the measurement. When using long cables, the filter
capacitance can be reduced or removed.
Application Circuit
Figure 23 shows a typical application circuit for the
NVT210, using a discrete sensor transistor connected via a
shielded, twisted pair cable. The pullups on SCLK, SDATA,
and ALERT
are required only if they are not provided
elsewhere in the system.
相关PDF资料 |
PDF描述 |
|---|---|
| HCC07DREI | CONN EDGECARD 14POS .100 EYELET |
| ZWQ805223 | PWRSUP QUAD 5V/+12V/-12V/3.3V |
| 5728-RC | CHOKE RF HI CURRENT 50UH 15% RAD |
| TPSB107K006H0250 | CAP TANT 100UF 6.3V 10% 1210 |
| A391J15C0GK5TAA | CAP CER 390PF 200V 5% NP0 AXIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NVT210DDM3R2G | 功能描述:板上安装温度传感器 TEMP SENSOR RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| NVT210DMTR2G | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| NVT-3402 | 制造商:Quest Technology International Inc 功能描述: |
| NVT-3403 | 制造商:Quest Technology International Inc 功能描述: |
| NVT4555UKZ | 功能描述:SIM Card Interface 12-WLCSP (1.20x1.60) 制造商:nxp semiconductors 系列:- 包装:剪切带（CT） 零件状态:停产 应用:SIM 卡 接口:- 电压 - 电源:1.1 V ~ 3.6 V 封装/外壳:12-UFBGA 供应商器件封装:12-WLCSP（1.20x1.60） 安装类型:表面贴装 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。