参数资料
型号: NVT210CMTR2G
厂商: ON Semiconductor
文件页数: 9/20页
文件大小: 325K
描述: IC TEMP SENSOR DGTL 8-WDFN
标准包装: 3,000
功能: 温度监控系统(传感器)
传感器类型: 内部和外部
感应温度: 0°C ~ 127°C,-64°C ~ 191°C
精确度: ±2.5°C
拓扑: ADC,比较器,多路复用器,寄存器库
输出类型: 2 线串行,I²C?/SMBUS?
输出警报:
输出风扇:
电源电压: 2.8 V ~ 3.6 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 8-WFDFN
供应商设备封装: 8-WDFN(2x2)
包装: 带卷 (TR)
NVT210
http://onsemi.com
9
Table 7. TEMPERATURE DATA FORMAT
(TEMPERATURE HIGH BYTE)
Temperature
Binary
Offset Binary
(Note 1)
55癈
0 000 0000
(Note 2)
0 000 1001
0癈
0 000 0000
0 100 0000
+1癈
0 000 0001
0 100 0001
+10癈
0 000 1010
0 100 1010
+25癈
0 001 1001
0 101 1001
+50癈
0 011 0010
0 111 0010
+75癈
0 100 1011
1 000 1011
+100癈
0 110 0100
1 010 0100
+125癈
0 111 1101
1 011 1101
+127癈
0 111 1111
1 011 1111
+150癈
0 111 1111
(Note 3)
1 101 0110
1.  Offset binary scale temperature values are offset by 64癈.
2.  Binary scale temperature measurement returns 0癈 for all
temperatures < 0癈.
3.  Binary scale temperature measurement returns 127癈 for all
temperatures > 127癈.
The user can switch between measurement ranges at any
time. Switching the range likewise switches the data format.
The next temperature result following the switching is
reported back to the register in the new format. However, the
contents of the limit registers do not change. It is up to the
user to ensure that when the data format changes, the limit
registers are reprogrammed as necessary. More information
on this is found in the Limit Registers section.
NVT210 Registers
The NVT210 contains 22, 8-bit registers in total. These
registers store the results of remote and local temperature
measurements, high and low temperature limits, and
configure and control the device. See the Address Pointer
Register section through the Consecutive ALERT
 Register
section of this data sheet for more information on the
NVT210 registers. Additional details are shown in Table 8
through Table 12. The entire register map is available in
Table 13.
Address Pointer Register
The address pointer register itself does not have, nor does
it require, an address because the first byte of every write
operation is automatically written to this register. The data
in this first byte always contains the address of another
register on the NVT210 that is stored in the address pointer
register. It is to this register address that the second byte of
a write operation is written, or to which a subsequent read
operation is performed.
The power-on default value of the address pointer register
is 0x00. Therefore, if a read operation is performed
immediately after power-on, without first writing to the
address pointer, the value of the local temperature is returned
because its register address is 0x00.
Temperature Value Registers
The NVT210 has three registers to store the results of local
and remote temperature measurements. These registers can
only be written to by the ADC and can be read by the user
over the SMBus/I
2
C. The local temperature value register is
at Address 0x00.
The external temperature value high byte register is at
Address 0x01, with the low byte register at Address 0x10.
The power-on default for all three registers is 0x00.
Configuration Register
The configuration register is Address 0x03 at read and
Address 0x09 at write. Its power-on default is 0x00. Only
four bits of the configuration register are used. Bit 0, Bit 1,
Bit 3, and Bit 4 are reserved; the user does not write to them.
Bit 7 of the configuration register masks the ALERT
output. If Bit 7 is 0, the ALERT
 output is enabled. This is the
power-on default. If Bit 7 is set to 1, the ALERT
 output is
disabled. This applies only if Pin 6 is configured as ALERT
.
If Pin 6 is configured as THERM2
, then the value of Bit 7
has no effect.
If Bit 6 is set to 0, which is power-on default, the device
is in operating mode with ADC converting. If Bit 6 is set to
1, the device is in standby mode and the ADC does not
convert. The SMBus/I
2
C does, however, remain active in
standby mode; therefore, values can be read from or written
to the NVT210 via the SMBus. The ALERT
 and THERM
outputs are also active in standby mode. Changes made to
the registers in standby mode that affect the THERM
 or
ALERT
 outputs cause these signals to be updated.
Bit 5 determines the configuration of Pin 6 on the
NVT210. If Bit 5 is 0 (default), then Pin 6 is configured as
an ALERT
 output. If Bit 5 is 1, then Pin 6 is configured as
a THERM2
 output. Bit 7, the ALERT
 mask bit, is only
active when Pin 6 is configured as an ALERT
 output. If
Pin 6 is set up as a THERM2
 output, then Bit 7 has no effect.
Bit 2 sets the temperature measurement range. If Bit 2 is
0 (default value), the temperature measurement range is set
between 0癈 to +127癈. Setting Bit 2 to 1 sets the
measurement range to the extended temperature range
(64癈 to +191癈).
相关PDF资料
PDF描述
HCC07DREI CONN EDGECARD 14POS .100 EYELET
ZWQ805223 PWRSUP QUAD 5V/+12V/-12V/3.3V
5728-RC CHOKE RF HI CURRENT 50UH 15% RAD
TPSB107K006H0250 CAP TANT 100UF 6.3V 10% 1210
A391J15C0GK5TAA CAP CER 390PF 200V 5% NP0 AXIAL
相关代理商/技术参数
参数描述
NVT210DDM3R2G 功能描述:板上安装温度传感器 TEMP SENSOR RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
NVT210DMTR2G 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
NVT-3402 制造商:Quest Technology International Inc 功能描述:
NVT-3403 制造商:Quest Technology International Inc 功能描述:
NVT4555UKZ 功能描述:SIM Card Interface 12-WLCSP (1.20x1.60) 制造商:nxp semiconductors 系列:- 包装:剪切带(CT) 零件状态:停产 应用:SIM 卡 接口:- 电压 - 电源:1.1 V ~ 3.6 V 封装/外壳:12-UFBGA 供应商器件封装:12-WLCSP(1.20x1.60) 安装类型:表面贴装 标准包装:1