- 您现在的位置：买卖IC网 > Datasheet目录629 > P1641100 (Red Lion Controls)P16 ANALOG CONTROLLER Datasheet资料下载
参数资料
| 型号： | P1641100 |
| 厂商： | Red Lion Controls |
| 文件页数： | 5/28页 |
| 文件大小： | 0K |
| 描述： | P16 ANALOG CONTROLLER |
| 标准包装： | 1 |
| 系列： | P16 |
| 类型： | 处理控制器 |
| 输入类型： | 电流，电压 |
| 控制器类型： | 成比例（PID） |
| 输出类型： | 继电器 |
| 电源电压： | 85 ~ 240VAC |
| 尺寸： | 48mm W x 48mm H（1/16 DIN） |
| 显示器类型： | LCD; 3 位（2） |
| 其它名称： | Q2676165 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
1.0 S ETTING
THE
J UMPERS
(A NALOG O UTPUT M ODELS O NLY )
TRO
N C .S.A.
RED
LIO U
E IN
. M
, PA
YO
Toinsureproperoperation,theAnalogOutputjumpersmustbesettothesame
range selected in programming Module 2-OP. The default jumper setting
is for 20 mA. The default setting in Module 2-OP is 4-20 mA. To
access the jumpers, insert a flat-blade screwdriver between the front
panel and the side case slot. This should disengage the top and
bottom front panel latches from the case grooves. Pull the
front panel assembly with the controller boards out of
the case. The jumpers are located inside the
controller on the left board along the back
top section.
RK
AD
ON
LS
RDY
A2
F1
A1
01
02
° %
MA N
%P W
10V (Both jumpers toward
the front of the unit)
20mA (Both jumpers toward
the rear of the unit)
VIEW FROM TOP OF UNIT
2.0 I NSTALLING
THE
C ONTROLLER
controllers are designed to be
mounted into an enclosed panel.
PANEL
MOUNTING LATCHING
SCREW SLOTS
PANEL LATCH
in-lb (79 N-cm). Overtightening can result in 1.772 +0.024
distortion of the controller, and reduce the
(45 +0.6 )
may affect proper operation.
The T16 and P16 controllers meet NEMA 4X/IP65 requirements for indoor
use to provide a watertight seal in steel panels with a minimum thickness of
0.09", or aluminum panels with a
minimum thickness of 0.12". The
PANEL GASKET
The bezel assembly must be in
place during installation of BEZEL
the controller.
PANEL
13
14
6
7
8
9
10
LATCHING
TABS
Instructions:
1. Prepare the panel cutout to the proper dimensions.
2. Remove the panel latch from the controller. Discard the cardboard sleeve.
3. Carefully remove the center section of the panel gasket and discard. Slide the
panel gasket over the rear of the controller, seating it against the lip at the
front of the case.
4. Insert the controller into the panel cutout. While holding the controller in
place, push the panel latch over the rear of the controller, engaging the tabs
of the panel latch in the farthest forward slot possible.
5. To achieve a proper seal, tighten the panel latch
screws evenly until the controller is snug in the
panel, torquing the screws to approximately 7
-0.000
-0.0
effectiveness of the seal. (45 +0.6 )
Note: The installation location of the controller is
important. Be sure to keep it away from heat
sources (ovens, furnaces, etc.) and away from
-0.000
direct contact with caustic vapors, oils, steam, or 1.772 +0.024
any other process by-products in which exposure
-0.0
Multiple Controller Stacking
The controller is designed to allow for close spacing of multiple controllers
in applications that do not require protection to NEMA 4X. Controllers can be
stacked either horizontally or vertically. For vertical stacking, install the panel
latch with the screws to the sides of the controller. For horizontal stacking, the
panel latch screws should be at the top and bottom of the controller. The
minimum spacing from centerline to centerline of controllers is 1.96" (49.8
mm). This spacing is the 1.96 (49.8)
same for vertical or MIN
horizontal stacking.
1.96 (49.8)
MAX
2.39 (60.7)
MAX.
1.96 (49.8)
MAX.
Note: When stacking
controllers, provide
adequate panel
ventilation to ensure
that the maximum
operating temperature
range is not exceeded.
STANDARD
PANEL
CUT-OUT
IF NEMA 4 IS NOT REQUIRED,
THIS PANEL MATERIAL MAY BE REMOVED.
2.39 (60.7)
MAX
5
相关PDF资料 |
PDF描述 |
|---|---|
| P1Z9ACR900W12 | DIODE MOD PWR-BRIK DL 1200V 740A |
| PA3716 | TOOL REPLACEMENT HEAD SET |
| PAXCDL10 | ANALOG OUTPUT CARD |
| PAXLC800 | COUNTER 8-DIGIT BI-DIR COUNT |
| PAXLPT00 | METER PROCESS TIME 6-DIGIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P1641110 | 制造商:Red Lion Controls 功能描述:PROCESS CONTR, 1/16DIN DC ANALOG 2 ALRM 制造商:Red Lion Controls 功能描述:DC W/ANALOG OUT 2 ALARMS |
| P1-64121 | 制造商:OTTO 功能描述:Pushbutton Switches Style F Scrw LoLev Red Button 制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Momentary Contact Screw Panel Mount |
| P1-64122 | 功能描述:按钮开关 Style F Scrw LoLev Black Button RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级: |
| P1-64122W | 制造商:OTTO 功能描述:Pushbutton Switches Style F Scrw LoLev Black Button 制造商:OTTO Engineering Inc 功能描述:STYLE F,SCREW,LOW |
| P1-64128 | 功能描述:按钮开关 Style F Scrw LoLev Gray Button RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级: |
发布紧急采购，3分钟左右您将得到回复。