- 您现在的位置：买卖IC网 > Datasheet目录629 > P1641100 (Red Lion Controls)P16 ANALOG CONTROLLER Datasheet资料下载
参数资料
| 型号： | P1641100 |
| 厂商： | Red Lion Controls |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | P16 ANALOG CONTROLLER |
| 标准包装： | 1 |
| 系列： | P16 |
| 类型： | 处理控制器 |
| 输入类型： | 电流，电压 |
| 控制器类型： | 成比例（PID） |
| 输出类型： | 继电器 |
| 电源电压： | 85 ~ 240VAC |
| 尺寸： | 48mm W x 48mm H（1/16 DIN） |
| 显示器类型： | LCD; 3 位（2） |
| 其它名称： | Q2676165 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
The values shown for the displays are the factory settings.
SETPOINT VALUE (SP1) *
INTEGRAL TIME
??
?
T16
???? to ????
In?? ?
? 12?
? to ???? seconds
???
??
2?
P16
T16
SETPOINT VALUE (SP2) *
???? to ????
Integral action shifts the center point position of the proportional band to
eliminate error in the steady state. The higher the integral time, the slower the
response. The optimal integral time is best determined during PID Tuning. If
time is set to zero, the previous Integral output power value is maintained.
Offset Power can be used to provide Manual Reset.
DERIVATIVE TIME
???F ?
???? ?
?
?
???? to ????
?
???? to ????
2?? P16
Typically, the controller is operating with the Setpoint value in the bottom
display. There is no annunciator nor parameter indication for Setpoint in the
Display Loop. The parameter name alternates with the setpoint value in the
Hidden Loop. The Setpoint value can be changed, activated and stored by
pressing the arrow keys. This is the only parameter that can be configured as
read only in the Display Loop, but read/write in the Hidden Loop. It is possible
to store a second Setpoint value that can be selected in the Hidden Loop, by the
F1 key or the user input. Both Setpoint values are limited by the Setpoint Low
and High Limits in Input Module 1-IN .
% OUTPUT POWER *
??
?1?? to 1????
???
The % Output Power is shown with the %PW annunciator. The parameter
name alternates with the % Output Power value in the Hidden Loop. While the
controller is in Automatic Mode, this value is read only. When the controller is
placed in Manual Mode, the value can be changed, activated and stored by
pressing the arrow keys. For more details on % Output Power, see Control
Mode Explanations.
OUTPUT POWER OFFSET
?1?? to 1????
? ???
When the Integral Time is set to zero and the controller is in the Automatic
Mode, this parameter will appear after % Output Power. It is also shown with
the %PW annunciator illuminated. The power offset is used to shift the
proportional band to compensate for errors in the steady state. If Integral Action
is later invoked, the controller will re-calculate the internal integral value to
provide “bumpless” transfer and Output Power Offset will not be necessary.
PROPORTIONAL BAND
? to ???? seconds per repeat
??
Derivative time helps to stabilize the response, but too high of a derivative
time, coupled with noisy signal processes, may cause the output to fluctuate too
greatly, yielding poor control. Setting the time to zero disables derivative action.
ALARM 1 VALUE
???1 ?
? T16
??? P16
On models with alarms, the value for Alarm 1 can be entered here. The value
is either absolute (absolute alarm types) or relative to the Setpoint value
(deviation and band alarm types.) When Alarm 1 is programmed for ???? or
??n? , this parameter is not available. For more details on alarms, see Alarm
Module 4-AL .
ALARM 2 VALUE
???2 ?
? T16
??? P16
On models with alarms, the value for Alarm 2 can be entered here. The value
is either absolute (absolute alarm types) or relative to the Setpoint value
(deviation and band alarm types.) When Alarm 2 is programmed for ???? or
??n? , this parameter is not available. For more details on alarms, see the Alarm
Module ???? .
* Alternating indication only used in the Hidden Loop.
???? ?
? ???
??? to ?????
(% of full input range)
The proportional band should be set to obtain the best response to a process
disturbance while minimizing overshoot. A proportional band of 0.0% forces
the controller into On/Off Control with its characteristic cycling at Setpoint. For
more information, see Control Mode and PID Tuning Explanations.
8
相关PDF资料 |
PDF描述 |
|---|---|
| P1Z9ACR900W12 | DIODE MOD PWR-BRIK DL 1200V 740A |
| PA3716 | TOOL REPLACEMENT HEAD SET |
| PAXCDL10 | ANALOG OUTPUT CARD |
| PAXLC800 | COUNTER 8-DIGIT BI-DIR COUNT |
| PAXLPT00 | METER PROCESS TIME 6-DIGIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P1641110 | 制造商:Red Lion Controls 功能描述:PROCESS CONTR, 1/16DIN DC ANALOG 2 ALRM 制造商:Red Lion Controls 功能描述:DC W/ANALOG OUT 2 ALARMS |
| P1-64121 | 制造商:OTTO 功能描述:Pushbutton Switches Style F Scrw LoLev Red Button 制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Momentary Contact Screw Panel Mount |
| P1-64122 | 功能描述:按钮开关 Style F Scrw LoLev Black Button RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级: |
| P1-64122W | 制造商:OTTO 功能描述:Pushbutton Switches Style F Scrw LoLev Black Button 制造商:OTTO Engineering Inc 功能描述:STYLE F,SCREW,LOW |
| P1-64128 | 功能描述:按钮开关 Style F Scrw LoLev Gray Button RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级: |
发布紧急采购，3分钟左右您将得到回复。