- 您现在的位置：买卖IC网 > PDF目录367736 > P80C528FFP (NXP SEMICONDUCTORS) CMOS single-chip 8-bit microcontroller PDF资料下载
参数资料
| 型号： | P80C528FFP |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | CMOS single-chip 8-bit microcontroller |
| 中文描述： | 8-BIT, 16 MHz, MICROCONTROLLER, PDIP40 |
| 文件页数： | 10/26页 |
| 文件大小： | 447K |
| 代理商： | P80C528FFP |
Philips Semiconductors
Product specification
80C528/83C528
CMOS single-chip 8-bit microcontrollers
1995 Feb 02
10
– setting Read Bit Finished (RBF) when the
SCL clock pulse has finished and Write Bit
Finished (WBF) if there is no arbitration
loss detected (i.e., SDA = 0 while SDO = 1)
– setting a serial clock Low-to-High detected
(CLH) flag
– setting a Bus Busy (BB) flag on a START
condition and clearing this flag on a STOP
condition
– releasing the SCL line and clearing the
CLH, RBF and WBF flags to resume
transfer of the next serial data bit
– generating an automatic clock if the single
bit data register S1BIT is used in master
mode.
The following functions must be done in
software:
– handling the I
2
C START interrupts
– converting serial to parallel data when
receiving
– converting parallel to serial data when
transmitting
– comparing the received slave address with
its own
– interpreting the acknowledge information
– guarding the I
2
C status if RBF or WBF = 0.
Additionally, if acting as master:
– generating START and STOP conditions
– handling bus arbitration
– generating serial clock pulses if S1BIT is
not used.
Three SFRs control the bit-level I
2
C interface:
S1INT, S1BIT and S1SCS.
INTERRUPT SYSTEM
The interrupt structure of the 8XC528 is the
same as that used in the 80C51, but includes
two additional interrupt sources: one for the
third timer/counter, T2, and one for the I
2
C
interface. The interrupt enable and interrupt
priority registers are IE and IP.
IE: Interrupt Enable Register
This register is located at address A8H. Refer
to Table 3.
IE SFR (A8H)
ET1
ES
ES1
ET2
EA
EX1
ET0
EX0
7
6
5
4
3
2
1
0
IP: Interrupt Priority Register
This register is located at address B8H. Refer
to Table 4.
IP SFR (B8H)
PT1
PS
PS1
PT2
–
PX1
PT0
PX0
7
6
5
4
3
2
1
0
The interrupt vector locations and the
interrupt priorities are:
Source
Vector
0003H
002BH
0053H
000BH
0013H
001BH
0023H
Priority within Level
Address
IE0
TF2+EXF2
SI (I
2
C)
TF0
IE1
TF1
R1+T1
Highest
Lowest
Table 3.
Description of IE Bits
MNEMONIC
BIT
FUNCTION
EA
IE.7
General enable/disable control:
0 =
NO
interrupt is enabled.
1 =
ANY
individually enabled interrupt will be accepted.
ES1
IE.6
Enable
bit-level I
2
C I/O
interrupt
Enable
Timer 2
interrupt
ET2
IE.5
ES
IE.4
Enable
Serial Port
interrupt
ET1
IE.3
Enable
Timer 1
interrupt
EX1
IE.2
Enable
External
interrupt 1
ET0
IE.1
Enable
Timer 0
interrupt
EX0
IE.0
Enable
External
interrupt 0
Table 4.
Description of IP Bits
MNEMONIC
BIT
FUNCTION
–
IP.7
Reserved.
Bit-level I
2
C
interrupt priority level
PS1
IP.6
PT2
IP.5
Timer 2
interrupt priority level
PS
IP.4
Serial Port
interrupt priority level
PT1
IP.3
Timer 1
interrupt priority level
PX1
IP.2
External Interrupt 1
priority level
PT0
IP.1
Timer 0
interrupt priority level
PX0
IP.0
External Interrupt 0
priority level
相关PDF资料 |
PDF描述 |
|---|---|
| P83C528FFP | CMOS single-chip 8-bit microcontroller |
| P80C528FFPN | CMOS single-chip 8-bit microcontroller |
| P83C528FFPN | CMOS single-chip 8-bit microcontroller |
| P80C528EBA | 8-bit microcontrollers |
| P83C528EBA | 8-bit microcontrollers |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P80C528FFPN | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontroller |
| P80C528FHA | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontroller |
| P80C528FHAA | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontroller |
| P80C528FHB | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontroller |
| P80C528FHBB | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontroller |
发布紧急采购，3分钟左右您将得到回复。