参数资料
| 型号： | P87C52X2FN,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 10/62页 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU 256 RAM 40DIP |
| 产品培训模块： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 标准包装： | 9 |
| 系列： | 87C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 33MHz |
| 连通性： | EBI/EMI，UART/USART |
| 外围设备： | POR |
| 输入/输出数： | 32 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | OTP |
| RAM 容量： | 256 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-DIP（0.600"，15.24mm） |
| 包装： | 管件 |
| 其它名称： | 568-7912-5 568-7912-5-ND 568-8361-5 935269602112 P87C52X2FN P87C52X2FN,112-ND P87C52X2FN-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
Philips Semiconductors
Product data
P80C3xX2; P80C5xX2;
P87C5xX2
80C51 8-bit microcontroller family
4K/8K/16K/32K ROM/OTP, low voltage (2.7 to 5.5 V),
low power, high speed (30/33 MHz)
2003 Jan 24
18
Table 4. Timer 2 Operating Modes
RCLK + TCLK
CP/RL2
TR2
MODE
0
1
16-bit Auto-reload
0
1
16-bit Capture
1
X
1
Baud rate generator
X
0
(off)
Symbol
Position
Name and Significance
TF2
T2CON.7
Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set
when either RCLK or TCLK = 1.
EXF2
T2CON.6
Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and
EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2
interrupt routine. EXF2 must be cleared by software. EXF2 does not cause an interrupt in up/down
counter mode (DCEN = 1).
RCLK
T2CON.5
Receive clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock
in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock.
TCLK
T2CON.4
Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock
in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.
EXEN2
T2CON.3
Timer 2 external enable flag. When set, allows a capture or reload to occur as a result of a negative
transition on T2EX if Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to
ignore events at T2EX.
TR2
T2CON.2
Start/stop control for Timer 2. A logic 1 starts the timer.
C/T2
T2CON.1
Timer or counter select. (Timer 2)
0 = Internal timer (OSC/12 in 12-clock mode or OSC/6 in 6-clock mode)
1 = External event counter (falling edge triggered).
CP/RL2
T2CON.0
Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN2 = 1. When
cleared, auto-reloads will occur either with Timer 2 overflows or negative transitions at T2EX when
EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to auto-reload
on Timer 2 overflow.
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
C/T2
CP/RL2
SU01621
Bit Addressable
T2CON
Address = C8H
Reset Value = 00H
76
54
3
2
1
0
Figure 6. Timer/Counter 2 (T2CON) Control Register
相关PDF资料 |
PDF描述 |
|---|---|
| LPC1224FBD64/121,1 | MCU 32BIT 48K FLASH 4K 64-LQFP |
| C8051F930-GM | IC 8051 MCU 64K FLASH 32-QFN |
| MMC2107CFCPV33 | IC MCU 33MHZ 128K FLASH 144-LQFP |
| LPC11E14FHN33/401, | IC MCU 32BIT 32K 32HVQFN |
| C8051F507-IQ | IC 8051 MCU 32K FLASH 32-QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P87C54 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family 4K/8K/16K/32K ROM/OTP 128B/256B RAM low voltage 2.7 to 5.5 V, low power, high speed 30/33 MHz |
| P87C541 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| P87C54-1 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
| P87C541 S F76 | 制造商:Intel 功能描述:MCU 8-bit MCS51 8051 CISC 16KB EPROM 5V 40-Pin PDIP |
| P87C54-2 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
发布紧急采购，3分钟左右您将得到回复。