参数资料
型号: P89LPC9401FBD,557
厂商: NXP Semiconductors
文件页数: 20/59页
文件大小: 0K
描述: IC 80C51 MCU FLASH 8K 64-LQFP
标准包装: 450
系列: LPC900
核心处理器: 8051
芯体尺寸: 8-位
速度: 18MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,LCD,LED,POR,PWM,WDT
输入/输出数: 23
程序存储器容量: 8KB(8K x 8)
程序存储器类型: 闪存
RAM 容量: 256 x 8
电压 - 电源 (Vcc/Vdd): 2.4 V ~ 3.6 V
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 64-LQFP
包装: 托盘
其它名称: 935278626557
P89LPC9401_1
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 — 5 September 2005
27 of 59
Philips Semiconductors
P89LPC9401
8-bit two-clock 80C51 microcontroller with 32 segment
× 4 LCD driver
received, the 9th data bit goes into RB8 in Special Function Register SCON, while the stop
bit is not saved. The baud rate is programmable to either 1
16 or
1
32 of the CPU clock
frequency, as determined by the SMOD1 bit in PCON.
7.19.4 Mode 3
11 bits are transmitted (through TXD) or received (through RXD): a start bit (logic 0), 8
data bits (LSB rst), a programmable 9th data bit, and a stop bit (logic 1). In fact, Mode 3 is
the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable
and is determined by the Timer 1 overow rate or the Baud Rate Generator (described in
7.19.5 Baud rate generator and selection
The P89LPC9401 enhanced UART has an independent Baud Rate Generator. The baud
rate is determined by a baud rate preprogrammed into the BRGR1 and BRGR0 SFRs
which together form a 16-bit baud rate divisor value that works in a similar manner as
Timer 1 but is much more accurate. If the baud rate generator is used, Timer 1 can be
used for other timing functions.
The UART can use either Timer 1 or the baud rate generator output (see Figure 8). Note
that Timer T1 is further divided by 2 if the SMOD1 bit (PCON.7) is cleared. The
independent Baud Rate Generator uses OSCCLK.
7.19.6 Framing error
Framing error is reported in the status register (SSTAT). In addition, if SMOD0 (PCON.6)
is logic 1, framing errors can be made available in SCON.7 respectively. If SMOD0 is
logic 0, SCON.7 is SM0. It is recommended that SM0 and SM1 (SCON.7:6) are set up
when SMOD0 is logic 0.
7.19.7 Break detect
Break detect is reported in the status register (SSTAT). A break is detected when
11 consecutive bits are sensed LOW. The break detect can be used to reset the device
and force the device into ISP mode.
7.19.8 Double buffering
The UART has a transmit double buffer that allows buffering of the next character to be
written to SBUF while the rst character is being transmitted. Double buffering allows
transmission of a string of characters with only one stop bit between any two characters,
as long as the next character is written between the start bit and the stop bit of the
previous character.
Fig 8.
Baud rate sources for UART (Modes 1, 3)
baud rate modes 1 and 3
SBRGS = 1
SBRGS = 0
SMOD1 = 0
SMOD1 = 1
timer 1 overflow
(PCLK-based)
baud rate generator
(CCLK-based)
002aaa897
÷2
相关PDF资料
PDF描述
P89LPC9402FBD,557 IC 80C51 MCU FLASH 8K 64-LQFP
P89LPC954FBD44,151 IC 80C51 MCU FLASH 16K 44LQFP
P89LPC972FN,129 MCU 80C51 8KB FLASH 20DIP
P89LPC985FDH,529 IC 80C51 MCU KB FLASH 28TSSOP
P89V51RC2FA,512 IC 80C51 MCU FLASH 32K 44-PLCC
相关代理商/技术参数
参数描述
P89LPC9402 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 32 segment 4 LCD driver
P89LPC9402FBD 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 32 segment 4 LCD driver
P89LPC9402FBD,557 功能描述:8位微控制器 -MCU IC 80C51 MCU FLASH 8K RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
P89LPC9408 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with two-clock 80C51 core 8 kB 3 V byte-erasable flash, 32 segment x 4 LCD driver, 10-bit ADC
P89LPC9408FBD 功能描述:8位微控制器 -MCU 8K FL/10B ADC LCD DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT