- 您现在的位置：买卖IC网 > Datasheet目录240 > PAXLHV00 (Red Lion Controls)METER AC VOLT 3-DIGIT PNL MNT Datasheet资料下载
参数资料
| 型号： | PAXLHV00 |
| 厂商： | Red Lion Controls |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | METER AC VOLT 3-DIGIT PNL MNT |
| 产品目录绘图： | PAX Lite Series PAX Lite Series Cut Out |
| 标准包装： | 1 |
| 系列： | PAX®LITE |
| 类型： | 伏特表 |
| 测量范围： | 0 ~ 600VAC |
| 显示器样式： | 红色字符，黑色背景 |
| 显示器类型： | LED |
| 显示器正面尺寸： | 3.80" L x 1.95" W（96.5 x 49.5mm） |
| 显示器位数： | 3 |
| 显示器位数 - 高度： | 0.560"（14.22mm） |
| 背光： | 无 |
| 安装类型： | 面板安装 |
| 端子： | 端接块 |
| 电源电压： | 115VAC，230 VAC |
| 其它名称： | RLC111 |
1.0 I NSTALLING
THE
M ETER
Installation
The PAX meets NEMA 4X/IP65 requirements when properly installed. The
unit is intended to be mounted into an enclosed panel. Prepare the panel cutout
to the dimensions shown. Remove the panel latch from the unit. Slide the panel
gasket over the rear of the unit to the back
of the bezel. The unit should be installed
While holding the unit in place, push the panel latch over the rear of the unit
so that the tabs of the panel latch engage in the slots on the case. The panel latch
should be engaged in the farthest forward slot possible. To achieve a proper seal,
tighten the latch screws evenly until the unit is snug in the panel (Torque to
approximately 7 in-lbs [79N-cm]). Do not over-tighten the screws.
BEZEL
LATCHING
SLOTS
PANEL
fully assembled. Insert the unit
into the panel cutout.
PANEL
LATCH
Installation Environment
The unit should be installed in a location that does not exceed the maximum
operating temperature and provides good air circulation. Placing the unit near
devices that generate excessive heat should be avoided.
The bezel should be cleaned only with a soft cloth and neutral soap product.
Do NOT use solvents. Continuous exposure to direct sunlight may accelerate the
aging process of the bezel.
PANEL CUT-OUT
(92 -.0 )
PANEL
GASKET
LATCHING
TABS
-.00
3.62 +.03
+.8
-.00
-.0
1.77 +.02
(45 +.5 )
PANEL
MOUNTING
SCREWS
2.0 S ETTING
THE
S WITCHES
The meter has a switch, which must be checked and/or changed prior to
applying power. To access the switch, remove the meter base from the case by
firmly squeezing and pulling back on the side rear finger tabs. This should lower
the latch below the case slot (which is located just in front of the finger tabs). It
is recommended to release the latch on one side, then start the other side latch.
Power Selection Switch
Caution: Insure the AC power selection switch is set for the
ON
4
3
2
1
proper voltage before powering-up the meter. The meter is shipped
from the factory in the 230 VAC position.
Set-Up DIP Switches
A DIP switch is located inside the meter. It is used for the selection of decimal
points and backlight annunciator. Selecting the “ON” position enables the
function.
SWITCH
1
2
3
4
FUNCTION
Decimal Point 1 (000.0)
Decimal Point 2 (00.00)
Decimal Point 3 (0.000)
Backlight Annunciator for Units Label
4
相关PDF资料 |
PDF描述 |
|---|---|
| PAXLIA00 | METER AC CURRENT 3 1/2-DIGIT |
| PAXLIT00 | METER AC CURRENT 5A 3 1/2-DIGIT |
| PAXLPV00 | METER PROCESS VOLT 3 1/2-DIGIT |
| PAXLRT00 | METER RTD TEMP 4-DIGIT |
| PAXLSG00 | METER STRAIN GAGE 3 1/2-DIGIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PAXLIA00 | 功能描述:METER AC CURRENT 3 1/2-DIGIT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030 |
| PAXLID00 | 功能描述:METER DC CURRENT 3 1/2-DIGIT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030 |
| PAXLIT00 | 功能描述:METER AC CURRENT 5A 3 1/2-DIGIT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030 |
| PAXLPT00 | 功能描述:METER PROCESS TIME 6-DIGIT RoHS:是 类别:工业控制，仪表 >> 定时器 系列:PAX®LITE 标准包装:10 系列:- 计时范围:- 工作模式:累积 输出类型:- 电源电压:4.5 V ~ 10 V 端接类型:PCB 引脚 显示器类型:无显示器 其它名称:2001PC-001 5VDCQ1273012Q1443992 |
| PAXLPV00 | 功能描述:METER PROCESS VOLT 3 1/2-DIGIT RoHS:否 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030 |
发布紧急采购，3分钟左右您将得到回复。