- 您现在的位置：买卖IC网 > Datasheet目录240 > PAXLPV00 (Red Lion Controls)METER PROCESS VOLT 3 1/2-DIGIT Datasheet资料下载
参数资料
| 型号： | PAXLPV00 |
| 厂商： | Red Lion Controls |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | METER PROCESS VOLT 3 1/2-DIGIT |
| 标准包装： | 1 |
| 系列： | PAX®LITE |
| 类型： | 伏特表 |
| 测量范围： | 0 ~ 25 VDC |
| 显示器样式： | 红色字符，黑色背景 |
| 显示器类型： | LED |
| 显示器正面尺寸： | 3.80" L x 1.95" W（96.5 x 49.5mm） |
| 显示器位数： | 3.5 |
| 显示器位数 - 高度： | 0.560"（14.22mm） |
| 背光： | 无 |
| 安装类型： | 面板安装 |
| 端子： | 螺钉端子 |
| 电源电压： | 85 ~ 250VAC |
| 其它名称： | RLC113 |
4.0 S CALING
THE
M ETER
PAXLPV SCHEMATIC
DESCRIPTION OF OPERATION
The PAX Lite Process Volt Meter consists of a digital volt meter combined with an analog scaling circuit
(shown above). Input voltage can be reversed in polarity resulting in negative numerical readout with a minus
(-) sign displayed. Input terminals 3 and 4 are connected to the signal voltage. The buffer amplifier (K1)
conditions and filters the input signal voltage and applies it to the input of the scaling circuit. The procedure
for scaling PAX Lite Process Volt Meters is simplified by dividing the scaling process into two separate
components, span adjustments and offset adjustments which are defined in the following discussion.
SPAN ADJUSTMENTS
Span is defined as the numerical range that the display traverses, disregarding
decimal points, when the input signal is varied from minimum to maximum. For
example, if a unit is to display 25.0 @ 1 V and 100.0 @ 5 V, the span is 750 (the
difference between 250 and 1000) . Had the minimum display been -25.0 @ 1 V
and +100.0 @ 5 V, the span would be 1250 (1000 - (-250) = 1250). (Note: the
terms “GAIN,” “SCALE,” and “SENSITIVITY” are also frequently used
interchangeably with the term “SPAN.”) The PAX Lite Process Volt Meter can
be set up over a very wide span range by means of the coarse DIP switches S6-
S10, and the fine screwdriver adjustment pot, located at the back cover. The
coarse span switches add parallel input resistors to the summing amplifier (K2),
thereby increasing its gain, or sensitivity, as
more summing resistors are added.
Effectively, adding more parallel input
resistors increases the slope of the transfer
curve (at right) and increases the numerical
readout for a given input signal change. The
input summing resistor values are weighted in
a binary progression, so they can be switched
in combinations to give 32 discrete steps of
span. The fine adjust control brackets these
coarse steps and can be adjusted to the exact
span needed.
The approximate span contributed by each switch is shown on the rear label.
The values shown are “units per volt.” For example, if S6 only is turned “ON,”
the numerical readout will change approximately 550 units for a signal voltage
change of 1 volt. If S7 were also turned “ON,” the numerical readout would
change approximately 825 units for a signal voltage change of 1 volt. The span
adjust pot has a continuous span range of approximately 0- 45.
6
OFFSET ADJUSTMENTS
Effectively, adding more parallel input
resistors increases the slope of the
transfer curve (at right) and increases the
numerical readout for a given input
signal change. In the foregoing
discussion of span, the transfer curves
were shown as “ZERO-BASED,” i.e.,
the numerical readout displays “0” when
the signal goes to zero. With voltage
ranges such as 0-5 V or 0-10 V, and with
Bi-Polar (+/-) signals this is often the
desired condition. However, with voltage
ranges such as 1-5 V or 1-10 V, the minimum voltage level usually represents
the zero level of the parameter being displayed. There are also many
applications where the minimum (or zero level) represents some value that does
not fall on a zero based transfer curve. To accommodate non-zero based
applications, the PAX Lite Process Volt Meter has provisions for offsetting the
transfer curve over a wide range. Essentially, offset moves the transfer curve up
or down to change its intercept with the numerical readout axis, but it does not
change the slope (SPAN) of the transfer curve. In the PAX Lite Process Volt
Meter, offset is accomplished by adding (or subtracting) a constant at the input
of the summing amplifier (K2). This offset constant is summed in with a
switched binary resistor network and a fine adjust offset control in a similar
manner to that used for span adjust. Switches S2-S5 can be turned on in
combinations to give 16 different coarse offset levels. Each switch is labeled to
show the approximate amount of offset contributed when it is turned “ON.”
Switch 1 selects the polarity of the switched-in offset value and allows
offsetting the transfer curve “UP” (adding the offset constant) or “DOWN”
(subtracting). The offset adjust pot has a numerical readout range of +/-100 and
brackets all the coarse switched ranges.
相关PDF资料 |
PDF描述 |
|---|---|
| PAXLRT00 | METER RTD TEMP 4-DIGIT |
| PAXLSG00 | METER STRAIN GAGE 3 1/2-DIGIT |
| PAXLTC00 | METER THERMOCOUPLE 4-DIGIT |
| PAXLVA00 | VOLTMETER AC 3 1/2-DIGIT |
| PAXLVD00 | VOLTMETER DC 3 1/2-DIGIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PAXLR000 | 功能描述:METER RATE INDICATION 6-DIGIT RoHS:是 类别:工业控制，仪表 >> 计数器 系列:PAX®LITE, PAXLR 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮 |
| PAXLRT00 | 功能描述:METER RTD TEMP 4-DIGIT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030 |
| PAXLSG00 | 功能描述:METER STRAIN GAGE 3 1/2-DIGIT RoHS:否 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030 |
| PAXLT000 | 制造商:Red Lion Controls 功能描述:METER, TC/RTD TEMP WITH DUAL RELAY 制造商:Red Lion Controls 功能描述:TC/RTD TEMP WITH DUAL RELAY |
| PAXLT0U0 | 制造商:Red Lion Controls 功能描述:METER, UL LISTED TC/RTD TEMP W/ D RELAY 制造商:Red Lion Controls 功能描述:UL LISTED TC/RTD TEMP WITH DUAL |
发布紧急采购，3分钟左右您将得到回复。