参数资料
| 型号： | PCA9507DP,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 13/20页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 24B 8TSSOP |
| 产品培训模块： | I²C Bus Fundamentals |
| 特色产品： | NXP - I2C Interface |
| 标准包装： | 1 |
| 接口： | I²C，SM 总线 |
| 输入/输出数： | 2 输入，2 输出 |
| 中断输出： | 无 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 标准包装 |
| 其它名称： | 568-5924-6 |
PIC16C77X
DS30275A-page 20
Advance Information
1999 Microchip Technology Inc.
2.2.2.5
PIR1 REGISTER
This register contains the individual flag bits for the
peripheral interrupts.
FIGURE 2-7:
PIR1 REGISTER (ADDRESS 0Ch)
Note:
Interrupt flag bits get set when an interrupt
condition occurs regardless of the state of
its corresponding enable bit or the global
enable bit, GIE (INTCON<7>). User soft-
ware should ensure the appropriate inter-
rupt flag bits are clear prior to enabling an
interrupt.
R/W-0
R-0
R/W-0
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
R
= Readable bit
W = Writable bit
U
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit7
bit0
bit 7:
PSPIF(1): Parallel Slave Port Read/Write Interrupt Flag bit
1 = A read or a write operation has taken place (must be cleared in software)
0 = No read or write has occurred
bit 6:
ADIF: A/D Converter Interrupt Flag bit
1 = An A/D conversion completed (must be cleared in software)
0 = The A/D conversion is not complete
bit 5:
RCIF: USART Receive Interrupt Flag bit
1 = The USART receive buffer is full (cleared by reading RCREG)
0 = The USART receive buffer is empty
bit 4:
TXIF: USART Transmit Interrupt Flag bit
1 = The USART transmit buffer is empty (cleared by writing to TXREG)
0 = The USART transmit buffer is full
bit 3:
SSPIF: Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
bit 2:
CCP1IF: CCP1 Interrupt Flag bit
Capture Mode
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare Mode
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM Mode
Unused in this mode
bit 1:
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
bit 0:
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflowed (must be cleared in software)
0 = TMR1 register did not overflow
Note 1: PSPIF is reserved on the 28-pin devices, always maintain this bit clear.
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9670PW,112 | IC I/O EXPANDER I2C 8B 16TSSOP |
| PCA9574BS,118 | IC I/O EXPANDER I2C 8B 16HVQFN |
| ATTINY24A-MUR | MCU AVR 2KB FLASH 20MHZ 20QFN |
| PCA8574PW,118 | IC I/O EXPANDER I2C 8B 16TSSOP |
| ATTINY24A-CCUR | MCU AVR 2KB FLASH 20MHZ 15UFBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9507DP-T | 功能描述:接口-信号缓冲器、中继器 LEVEL TRANSL I2C BUS REPEATER RoHS:否 制造商:Texas Instruments 工作电源电压: 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:VSSOP-8 封装:Reel |
| PCA9507D-T | 功能描述:接口-信号缓冲器、中继器 LEVEL TRANSL I2C BUS REPEATER RoHS:否 制造商:Texas Instruments 工作电源电压: 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:VSSOP-8 封装:Reel |
| PCA9508 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Smart, simple solutions for the 12 most common design concerns |
| PCA9508D | 功能描述:接口-信号缓冲器、中继器 HOTSWAP LVTTL I2C-BUS REPEATER RoHS:否 制造商:Texas Instruments 工作电源电压: 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:VSSOP-8 封装:Reel |
| PCA9508D,112 | 功能描述:接口-信号缓冲器、中继器 HOTSWAP LVTTL RoHS:否 制造商:Texas Instruments 工作电源电压: 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:VSSOP-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。