参数资料
| 型号： | PCA9621D,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 13/18页 |
| 文件大小： | 0K |
| 描述： | IC BUS OUTPUT PORT 2WIRE 16SOIC |
| 产品培训模块： | I²C Bus Fundamentals |
| 特色产品： | NXP - I2C Interface |
| 标准包装： | 1 |
| 接口： | I²C 总线，SM 总线 |
| 输入/输出数： | 8 |
| 中断输出： | 无 |
| 频率 - 时钟： | 1MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SO |
| 包装： | 标准包装 |
| 其它名称： | 568-6671-6 |
PCA9621
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 1 — 9 March 2011
4 of 18
NXP Semiconductors
PCA9621
65 mA 8-bit 2-wire bus output port
7.
Functional description
Refer to Figure 1 “Block diagram of PCA9621”.
7.1 VDD, VSS — DC supply pins
The power supply voltage for the PCA9621 may be any voltage in the range 2.7 V to
5.5 V. All other I/Os are clamped to VDD and VSS through ESD protection diodes.
7.2 SCL, SDA — 2-wire bus interface
The state of the output ports is determined by the Control register, which is set and read
via a 2-wire bus interface using I2C-bus style signalling. The interface is Fast-mode Plus
(Fm+) I2C-bus compatible, though the ports contain ESD protection diodes to the positive
and negative supplies. Consequently, VI2C-bus (voltage at SCL and SDA) must remain
within the VDD and VSS supply levels.
7.3 P0 to P7 — output ports
There are eight open-drain output ports whose state is determined by the Control register.
Programming a ‘1’ or HIGH to the relevant register bit will turn on the corresponding port,
resulting at a LOW or ‘0’ at the port. In the case of LED driving, this would result in the
LED turning ON.
Programming a ‘0’ or LOW in the register turns off the open-drain port, placing it in a
high-impedance mode.
The ports are protected by ESD diodes to the supplies so they must not be driven above
the VDD or below the VSS levels.
7.4 RESET — reset IC to default state
The active LOW RESET input is used to disable the buffer and reset it to its default state.
The RESET signal will clear the contents of the Control register, turning off all output
ports, and resetting the state of the I2C-bus slave transceiver block.
7.5 Power-On Reset (POR)
During power-on, the PCA9621 is internally held in the reset condition for a maximum of
trst = 500 ns. The default condition after reset is for the Control register to be erased
(all zeros), resulting in all output ports being off (high-impedance).
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9536DP/DG,118 | IC I/O EXPANDER I2C 4B 8TSSOP |
| PCF8575TS/1,118 | IC I/O EXPANDER I2C 16B 24SSOP |
| PCA9539D,118 | IC I/O EXPANDER I2C 16B 24SOIC |
| PCA9555DB,118 | IC I/O EXPANDER I2C 16B 24SSOP |
| ATTINY13A-SFR | IC MCU AVR 1K FLASH 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9621PW,118 | 功能描述:数字总线开关 IC 65 mA 8-Bit 2-Wire Bus Output Port RoHS:否 制造商:Texas Instruments 开关数量:24 传播延迟时间:0.25 ns 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:TSSOP-56 封装:Reel |
| PCA9622BS,118 | 功能描述:LED照明驱动器 16-BIT FM+ I2C-BUS 100MA 40V LED DRIVER RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| PCA9622DR | 制造商:NXP Semiconductors 功能描述:IC LED DRIVER RGBA 32-TSSOP 制造商:NXP Semiconductors 功能描述:IC, LED DRIVER, RGBA, 32-TSSOP 制造商:NXP Semiconductors 功能描述:IC, LED DRIVER, RGBA, 32-TSSOP; No. of Outputs:16; Output Current:100mA; Output Voltage:40V; Driver Case Style:TSSOP; Input Voltage Min:2.3V; Input Voltage Max:5.5V; Dimming Control Type:PWM; Switching Frequency:1MHz; Operating ;RoHS Compliant: Yes |
| PCA9622DR,118 | 功能描述:LED照明驱动器 16-BIT FM+ I2C-BUS 100mA 40V LED driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| PCA9622DR,118-CUT TAPE | 制造商:NXP 功能描述:PCA9622 Series 100 mA 5.5 V 1 MHz SMT 16-bit I2C-Bus LED Driver - TSSOP-32 |
发布紧急采购，3分钟左右您将得到回复。