参数资料
型号: PCA9633DP2,118
厂商: NXP Semiconductors
文件页数: 16/43页
文件大小: 0K
描述: IC LED DRIVER RGBA 10-TSSOP
产品培训模块: LED Controllers
I²C Bus Fundamentals
标准包装: 1
拓扑: 开路漏极,PWM
输出数: 4
内部驱动器: 两者兼有
类型 - 主要: 背光,LED 闪烁器
类型 - 次要: RGBA
频率: 25MHz
电源电压: 2.3 V ~ 5.5 V
输出电压: 5.5V
安装类型: 表面贴装
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)
供应商设备封装: 10-TSSOP
包装: 标准包装
工作温度: -40°C ~ 85°C
产品目录页面: 845 (CN2011-ZH PDF)
配用: OM6276,598-ND - DEMO BOARD PWM LED
622-1004-ND - BOARD DEMO FOR PHILIPS PCA9633
其它名称: 568-3237-6
NXP Semiconductors
PCA9633
4-bit Fm+ I 2 C-bus LED driver
7.4 Active LOW output enable input
The active LOW output enable (OE) pin, allows to enable or disable all the LED outputs at
the same time.
This control signal is only available for the 16-pin version and does not apply to the 8-pin
or 10-pin versions.
? When a LOW level is applied to OE pin, all the LED outputs are enabled and follow the
output state de?ned in the LEDOUT register with the polarity de?ned by INVRT bit
(MODE2 register).
? When a HIGH level is applied to OE pin, all the LED outputs are programmed to the
value that is de?ned by OUTNE[1:0] in the MODE2 register.
Table 16.
LED outputs when OE = 1
OUTNE1
0
0
1
1
OUTNE0
0
1
0
1
LED outputs
0
1 if OUTDRV = 1, high-impedance if OUTDRV = 0
high-impedance
reserved
The OE pin can be used as a synchronization signal to switch on/off several PCA9633
devices at the same time. This requires an external clock reference that provides blinking
period and the duty cycle.
The OE pin can also be used as an external dimming control signal. The frequency of the
external clock must be high enough not to be seen by the human eye, and the duty cycle
value determines the brightness of the LEDs.
Remark: Do not use OE as an external blinking control signal when internal global
blinking is selected (DMBLNK = 1, MODE2 register) since it will result in an unde?ned
blinking pattern. Do not use OE as an external dimming control signal when internal global
dimming is selected (DMBLNK = 0, MODE2 register) since it will result in an unde?ned
dimming pattern.
7.5 Power-on reset
When power is applied to V DD , an internal Power-on reset holds the PCA9633 in a reset
condition until V DD has reached V POR . At this point, the reset condition is released and the
PCA9633 registers and I 2 C-bus state machine are initialized to their default states (all
zeroes) causing all the channels to be deselected. Thereafter, V DD must be lowered below
0.2 V to reset the device.
PCA9633_5
? NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 25 July 2008
16 of 43
相关PDF资料
PDF描述
VJ1206A200JBAAT4X CAP CER 20PF 50V 5% NP0 1206
B82422A1822K100 INDUCTOR 8.2UH 130MA 1210 10%
1-745968-4 CONN D-SUB PLUG STR 25POS PCB AU
EP2AGX65DF29I3N IC ARRIA II GX FPGA 65K 780FBGA
1571650-5 CONN PLUG 9POS SLD CUP 20AWG
相关代理商/技术参数
参数描述
PCA9633PW 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633PW,112 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633PW,118 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633TK,118 功能描述:LED照明驱动器 4-BIT I2C FM+ TP LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633TK-T 功能描述:LED照明驱动器 4-BIT I2C FM+ TP LED CON RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N