参数资料
型号: PCA9685BS,118
厂商: NXP Semiconductors
文件页数: 14/51页
文件大小: 0K
描述: IC LED DVR PWM 16CH HVQFN28
产品培训模块: I²C Bus Fundamentals
标准包装: 1
拓扑: 开路漏极,PWM
输出数: 16
内部驱动器:
类型 - 主要: 背光,LED 闪烁器
类型 - 次要: RGBA
频率: 25MHz,50MHz
电源电压: 2.3 V ~ 5.5 V
输出电压: 5.5V
安装类型: 表面贴装
封装/外壳: 28-VQFN 裸露焊盘
供应商设备封装: 28-HVQFN(6x6)
包装: 标准包装
工作温度: -40°C ~ 85°C
其它名称: 568-5305-6
NXP Semiconductors
PCA9685
16-channel, 12-bit PWM Fm+ I 2 C-bus LED controller
7.3.1.1
Restart mode
If the PCA9685 is operating and the user decides to put the chip to sleep (setting MODE1
bit 4) without stopping any of the PWM channels, the RESTART bit (MODE1 bit 7) will be
set to logic 1 at the end of the PWM refresh cycle. The contents of each PWM register are
held valid when the clock is off.
To restart all of the previously active PWM channels with a few I 2 C-bus cycles do the
following steps:
1. Read MODE1 register.
2. Check that bit 7 (RESTART) is a logic 1. If it is, clear bit 4 (SLEEP). Allow time for
oscillator to stabilize (500 μ s).
3. Write logic 1 to bit 7 of MODE1 register. All PWM channels will restart and the
RESTART bit will clear.
Remark: The SLEEP bit must be logic 0 for at least 500 μ s, before a logic 1 is written into
the RESTART bit.
Other actions that will clear the RESTART bit are:
1. Power cycle.
2. I 2 C Software Reset command.
3. If the MODE2 OCH bit is logic 0, write to any PWM register then issue an I 2 C-bus
STOP.
4. If the MODE2 OCH bit is logic 1, write to all four PWM registers in any PWM channel.
Likewise, if the user does an orderly shutdown 1 of all the PWM channels before setting
the SLEEP bit, the RESTART bit will be cleared. If this is done the contents of all PWM
registers are invalidated and must be reloaded before reuse.
An example of the use of the RESTART bit would be the restoring of a customer ’s laptop
LCD backlight intensity coming out of Standby to the level it was before going into
Standby.
1.
Two methods can be used to do an orderly shutdown. The fastest is to write a logic 1 to bit 4 in register ALL_LED_OFF_H. The
other method is to write logic 1 to bit 4 in each active PWM channel LEDn_OFF_H register.
PCA9685
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 2 September 2010
? NXP B.V. 2010. All rights reserved.
14 of 51
相关PDF资料
PDF描述
VI-BWD-CV-F4 CONVERTER MOD DC/DC 85V 150W
ESC60DREF-S734 CONN EDGECARD 120POS .100 EYELET
TAP686K010FCS CAP TANT 68UF 10V 10% RADIAL
VI-BWJ-CV-F1 CONVERTER MOD DC/DC 36V 150W
ABM02DRTN CONN EDGECARD 4POS DIP .156 SLD
相关代理商/技术参数
参数描述
PCA9685PW 制造商:NXP Semiconductors 功能描述:IC LED DRIVER RGBA 28-TSSOP 制造商:NXP Semiconductors 功能描述:IC, LED DRIVER, RGBA, 28-TSSOP 制造商:NXP Semiconductors 功能描述:IC, LED DRIVER, RGBA, 28-TSSOP; No. of Outputs:16; Output Current:25mA; Output Voltage:5.5V; Driver Case Style:TSSOP; Input Voltage Min:2.3V; Input Voltage Max:5.5V; Dimming Control Type:PWM; Switching Frequency:1MHz; Operating ;RoHS Compliant: Yes
PCA9685PW,112 功能描述:LED显示驱动器 I2C Bus LED Controller 28-Pin RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
PCA9685PW,118 功能描述:LED显示驱动器 I2C Bus LED Controller 28-Pin RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
PCA9685PW/Q900,118 功能描述:LED显示驱动器 LED Driver 2.3V-5.5V 6mA RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
PCA9691BS/1 制造商:NXP Semiconductors 功能描述:IC ADC/DAC 8-BIT I2C 16-HVQFN 制造商:NXP Semiconductors 功能描述:IC, ADC/DAC, 8-BIT, I2C, 16-HVQFN