- 您现在的位置：买卖IC网 > PDF目录4384 > PCF8582C-2P/03,112 (NXP Semiconductors)IC EEPROM 2KBIT 100KHZ 8DIP PDF资料下载
参数资料
| 型号： | PCF8582C-2P/03,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 17/21页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 2KBIT 100KHZ 8DIP |
| 产品培训模块： | I²C Bus Fundamentals |
| 特色产品： | NXP - I2C Interface |
| 标准包装： | 50 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 2K (256 x 8) |
| 速度： | 100kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.5 V ~ 6.0 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-DIP |
| 包装： | 管件 |
| 产品目录页面： | 827 (CN2011-ZH PDF) |
| 配用： | 568-4002-ND - DEMO BOARD I2C |
| 其它名称： | 568-3531-5 935191670112 PCF8582C2N |
Philips Semiconductors
PCF8582C-2
256 × 8-bit CMOS EEPROM with I 2 C-bus interface
– for packages with a thickness ≥ 2.5 mm
– for packages with a thickness < 2.5 mm and a volume ≥ 350 mm 3 so called
thick/large packages.
? below 240 ° C (SnPb process) or below 260 ° C (Pb-free process) for packages with
a thickness < 2.5 mm and a volume < 350 mm 3 so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing, must be respected at all
times.
9397 750 14222
15.3.2
15.3.3
Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was speci?cally
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
? Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
? For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
parallel to the transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
? For packages with leads on four sides, the footprint must be placed at a 45 ° angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
During placement and before soldering, the package must be ?xed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250 ° C or
265 ° C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated ?ux will eliminate the need for removal of corrosive residues in
most applications.
Manual soldering
Fix the component by ?rst soldering two diagonally-opposite end leads. Use a low
voltage (24 V or less) soldering iron applied to the ?at part of the lead. Contact time
must be limited to 10 seconds at up to 300 ° C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320 ° C.
? Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 — 25 October 2004
17 of 21
相关PDF资料 |
PDF描述 |
|---|---|
| EP4CGX110DF31C8 | IC CYCLONE IV FPGA 110K 896FBGA |
| M1A3PE3000-1PQG208 | IC FPGA 1KB FLASH 3M 208-PQFP |
| A3PE3000-1PQG208 | IC FPGA 1KB FLASH 3M 208-PQFP |
| A3PE3000-1PQ208 | IC FPGA 1KB FLASH 3M 208-PQFP |
| A3PE3000L-PQ208 | IC FPGA 1KB FLASH 3M 208-PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCF8582C-2T | 制造商:NXP Semiconductors 功能描述:Bulk |
| PCF8582C-2T/03 | 制造商:NXP Semiconductors 功能描述:EEPROM SERIAL 2K SMD 8582 SOIC8 制造商:NXP Semiconductors 功能描述:EEPROM SERIAL 2K, SMD, 8582, SOIC8 制造商:NXP Semiconductors 功能描述:IC, EEPROM, 2KBIT, I2C, 100KHZ, SOIC-8; Memory Size:2Kbit; Memory Configuration:2 BLK(256 x 8); Clock Frequency:100kHz; Supply Voltage Min:2.5V; Supply Voltage Max:6V; Memory Case Style:SOIC; No. of Pins:8; IC Interface Type:I2C ;RoHS Compliant: Yes 制造商:NXP Semiconductors 功能描述:Serial access EEPROM,PCF8582C-2T 2kb SO8 |
| PCF8582C-2T/03,112 | 功能描述:电可擦除可编程只读存储器 电可擦除可编程只读存储器 256X8 W/I2C 100KHZ -40+85 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| PCF8582C-2T/03,118 | 功能描述:电可擦除可编程只读存储器 256X8 电可擦除可编程只读存储器 I2C BUS SO-8 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| PCF8582C-2T/03 | 制造商:NXP Semiconductors 功能描述:EEPROM SERIAL 2K SMD 8582 SOIC8 |
发布紧急采购，3分钟左右您将得到回复。