- 您现在的位置：买卖IC网 > PDF目录98051 > PDT012A0X3-SRZ (LINEAGE POWER LLC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PDT012A0X3-SRZ |
| 厂商： | LINEAGE POWER LLC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT PACKAGE-17 |
| 文件页数： | 15/39页 |
| 文件大小： | 856K |
| 代理商： | PDT012A0X3-SRZ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Preliminary Data Sheet
May 4, 2011
12A Digital Pico DLynxTM: Non-isolated DC-DC Power Modules
3 – 14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A output
LINEAGE POWER
22
4.
Module output is disabled when the fault is
present and the output is enabled when the
fault no longer exists (Bits [7:6] = 11, Bits [5:3]
= xxx).
Note that separate response choices are possible for
output over voltage or under voltage faults.
PMBus Adjustable Input Undervoltage
Lockout
The module allows adjustment of the input under
voltage lockout and hysteresis. The command VIN_ON
allows setting the input voltage turn on threshold, while
the VIN_OFF command sets the input voltage turn off
threshold. For the VIN_ON command, possible values
are 2.75V, and 3V to 14V in 0.5V steps. For the
VIN_OFF command, possible values are 2.5V to 14V
in 0.5V steps. If other values are entered for either
command, they will be mapped to the closest of the
allowed values.
Both the VIN_ON and VIN_OFF commands use the
“Linear” format with two data bytes. The upper five bits
represent the exponent (fixed at -2) and the remaining
11 bits represent the mantissa. For the mantissa, the
four most significant bits are fixed at 0.
Power Good
The module provides a Power Good (PGOOD) signal
that is implemented with an open-drain output to
indicate that the output voltage is within the regulation
limits of the power module. The PGOOD signal will be
de-asserted to a low state if any condition such as
overtemperature, overcurrent or loss of regulation
occurs that would result in the output voltage going
outside the specified thresholds. The PGOOD
thresholds are user selectable via the PMBus (the
default values are as shown in the Feature
Specifications Section). Each threshold is set up
symmetrically above and below the nominal value. The
POWER_GOOD_ON command sets the output
voltage level above which PGOOD is asserted (lower
threshold). For example, with a 1.2V nominal output
voltage, the POWER_GOOD_ON threshold can set
the lower threshold to 1.14 or 1.1V. Doing this will
automatically set the upper thresholds to 1.26 or 1.3V.
The POWER_GOOD_OFF command sets the level
below which the PGOOD command is de-asserted.
This command also sets two thresholds symmetrically
placed around the nominal output voltage. Normally,
the POWER_GOOD_ON threshold is set higher than
the POWER_GOOD_OFF threshold.
Both POWER_GOOD_ON and POWER_GOOD_OFF
commands use the “Linear” format with the exponent
fixed at –10 (decimal). The two thresholds are given by
10
)
_
(
10
)
_
(
2
)
_
(
2
)
_
(
×
=
×
=
OFF
GOOD
POWER
V
ON
GOOD
POWER
V
OFF
PGOOD
OUT
ON
PGOOD
OUT
Both commands use two data bytes with bit [7] of the
high byte fixed at 0, while the remaining bits are r/w
and used to set the mantissa using two’s complement
representation. Both commands also use the
VOUT_SCALE_LOOP parameter so it must be set
correctly. The default value of POWER_GOOD_ON is
set at 1.1035V and that of the POWER_GOOD_OFF is
set at 1.08V. The values associated with these
commands can be stored in non-volatile memory using
the STORE_DEFAULT_ALL command.
The PGOOD terminal can be connected through a
pullup resistor (suggested value 100K
Ω) to a source of
5VDC or lower.
Measurement of Output Current, Output
Voltage and Input Voltage
The module is capable of measuring key module
parameters such as output current and voltage and
input voltage and providing this information through the
PMBus interface. Roughly every 200μs, the module
makes 16 measurements each of output current,
voltage and input voltage. Average values of of these
16 measurements are then calculated and placed in
the appropriate registers. The values in the registers
can then be read using the PMBus interface.
Measuring Output Current Using the PMBus
The module measures current by using the inductor
winding resistance as a current sense element. The
inductor winding resistance is then the current gain
factor used to scale the measured voltage into a
current reading. This gain factor is the argument of the
IOUT_CAL_GAIN command, and consists of two bytes
in the linear data format. The exponent uses the upper
five bits [7:3] of the high data byte in two-s
complement format and is fixed at –15 (decimal). The
remaining 11 bits in two’s complement binary format
represent the mantissa. During manufacture, each
module is calibrated by measuring and storing the
current gain factor into non-volatile storage.
The current measurement accuracy is also improved
by each module being calibrated during manufacture
with the offset in the current reading. The
IOUT_CAL_OFFSET command is used to store and
read the current offset. The argument for this
command consists of two bytes composed of a 5-bit
exponent (fixed at -4d) and a 11-bit mantissa. This
command has a resolution of 62.5mA and a range of
-4000mA to +3937.5mA.
The READ_IOUT command provides module average
output current information. This command only
supports positive or current sourced from the module.
If the converter is sinking current a reading of 0 is
provided. The READ_IOUT command returns two
bytes of data in the linear data format. The exponent
uses the upper five bits [7:3] of the high data byte in
two-s complement format and is fixed at –4 (decimal).
The remaining 11 bits in two’s complement binary
format represent the mantissa with the 11
th bit fixed at
0 since only positive numbers are considered valid.
Note that the current reading provided by the module
is not corrected for temperature. The temperature
corrected current reading for module temperature
TModule can be estimated using the following equation
相关PDF资料 |
PDF描述 |
|---|---|
| PDT012A0X3-SRDZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PE3236-54 | PHASE LOCKED LOOP, PQCC44 |
| PE3236-21 | PHASE LOCKED LOOP, PQCC44 |
| PE33361MLIAA-Z | PHASE LOCKED LOOP, QCC48 |
| PE33361MLIAA | PHASE LOCKED LOOP, QCC48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PDT012A0X43-SRZ | 功能描述:DC/DC转换器 3-14.4Vin .6-5.5Vout 12A PosLogic Digital RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PDT0311 | 制造商:AGILENT 制造商全称:AGILENT 功能描述:Connectorized PIN Photodiodes |
| PDT0311-FC-A | 制造商:AGILENT 制造商全称:AGILENT 功能描述:Connectorized PIN Photodiodes |
| PDT0312 | 制造商:AGILENT 制造商全称:AGILENT 功能描述:Connectorized PIN Photodiodes |
| PDT0312-FC-A | 制造商:AGILENT 制造商全称:AGILENT 功能描述:Connectorized PIN Photodiodes |
发布紧急采购，3分钟左右您将得到回复。