- 您现在的位置：买卖IC网 > PDF目录69043 > PFS763HG (POWER INTEGRATIONS INC) 4.16 A SWITCHING CONTROLLER, 70 kHz SWITCHING FREQ-MAX, PZIP16 PDF资料下载
参数资料
| 型号： | PFS763HG |
| 厂商： | POWER INTEGRATIONS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 4.16 A SWITCHING CONTROLLER, 70 kHz SWITCHING FREQ-MAX, PZIP16 |
| 封装： | HALOGEN FREE AND ROHS COMPLIANT, PLASTIC, SIP-16 |
| 文件页数： | 4/36页 |
| 文件大小： | 4692K |
| 代理商： | PFS763HG |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Rev. C 02/11
12
TFS757-764HG
www.powerint.com
are slightly different for the ENABLE pin versus the FEEDBACK
pin. The ENABLE pin internal current selection is chosen
according to the above table.
The current limit selection for both FEEDBACK pin and ENABLE
pin takes place when the BYPASS pin first reaches 4.7 V. Once
the short detection period is complete, the BYPASS pin is
ramped on up to 5.7 V, and the FEEDBACK pin is allowed to
float to it’s nominal voltage of 3.5 V.
Standby Line Compensated Current Limit
to Flatten Output Overload
For many power supplies, the power output capability of the
power supply increases dramatically as the input voltage
increases. This means that most power supplies are able to
deliver much more power (up to 30-40% more power), into a
fault overload when operating at higher input voltage (versus
operating at lower input voltage). This can cause a problem
since many specifications require that the output overload
power capability of the device is more tightly managed.
In the case of the HiperTFS, the standby current limit is adjusted
as a function of line (input voltage), in such a ways as to always
provide substantially the same maximum overload power
capability. The input voltage is detected via the LINE-SENSE
pin current and the internal standby current limit of the device is
adjusted accordingly on a cycle-by-cycle basis. This means that
the HiperTFS standby will only deliver approximately 5% more
overload power at high-line as it did at low-line. This feature
provides a much safer design.
Standby Line Undervoltage Detection (UV)
The LINE-SENSE pin resistor is connected to V
IN and generates
a current signal proportional to V
IN. The LINE-SENSE pin
voltage is held by the device at 2.35 V. The LINE-SENSE pin
current signal is used to trigger under/overvoltage thresholds for
both the standby and main converters. Assuming a LINE-SENSE
pin resistor of 4 MW, the standby will begin operating at
approximately 100 V (as defined by I
L(SB_UVON)). The standby will
shutdown if regulation is lost when input voltage is below 100 V.
However the standby will be forced to shutdown if this input
voltage drops below approximately 40 V (as defined by I
L(SB-UVOFF)).
Main and Standby Oscillator and Switching Frequency
The standby converter operates at a frequency of 132 kHz. The
main converter operates at exactly half that frequency at 66 kHz.
The two converters both include a common frequency jitter
profile that varies the switching frequency ±4 kHz for the main
(twice the jitter frequency range ±8 kHz for the standby), during
a 4 ms jitter period. The frequency jitter helps reduce quasi-
peak and average EMI emissions.
It should be noted that the HiperTFS has a collision avoidance
scheme in which the main converter is the master and the
standby is the slave, which avoids the main and standby switching
at exactly simultaneous moments. The most common
condition would be close to 50% duty cycle, if the main (master)
is about to switch (turn-off), then the standby (slave), waits for
short instant (200 ns) before starting it’s next cycle. The
standby is used as the slave, since the ON/OFF control of the
HiperTFS standby is less easily disrupted by sudden delays in
switching, versus the linear control loop of the main converter.
Standby and Main Thermal Shutdown
The HiperTFS provides a thermal shutdown function, (OTP) that
protects the HiperTFS. This hysteretic thermal shutdown allows
the device to automatically recover from any thermal fault event.
The thermal shutdown is triggered at a die-temperature of
approximately 118 °C and has a high hysteresis to ensure the
average device temperature is within safe levels. In a well
designed system the HiperTFS thermal shutdown is not
triggered during any normal operation and is only present as a
safety feature to protect against abnormal or fault conditions.
BYPASS (BP) Pin Operation
The BYPASS (BP) pin is the supply pin for the entire HiperTFS
device. The BYPASS pin is internally connected to a high-voltage
current source via the STANDBY DRAIN power MOSFET. This
high-voltage source will charge the BYPASS pin to 4.7 V during
initial power up. Once the BYPASS pin reaches 4.7 V, the
BYPASS pin will check the main and standby current limit
selection (FEEDBACK pin and ENABLE pin resistors respectively).
This selection takes a very short period, thereafter the BYPASS
pin continues being charged until it reaches 5.7 V, at which
point the standby power supply is ready to begin operation.
Like the TinySwitch-III the high-voltage current source will
continue to charge the BYPASS pin if it droops below 5.7 V.
However in most typical applications, a resistor (typically 7.5 kW)
is connected from primary bias (12 V) to the BYPASS pin. This
resistor provides the operating current to the BYPASS pin,
preventing the need to draw power from the high-voltage
current source. Like the TinySwitch-III, the BYPASS pin contains
a shunt regulator, which will be enabled if the BYPASS pin
voltage is externally driven above 5.7 V. The BYPASS pin shunt
current is used for two functions:
1. First, for a 4 mA threshold (I
BP(ON)) for main remote-on. When
the BYPASS pin current exceeds this threshold, the main is
enabled.
Figure 12. Shows Output Overload Power for Both Compensated and
Uncompensated Standby Current Limits.
50
100
150
200
250
300
400
450
350
VIN DC (V)
Output
Overload
Power
(%)
150
140
130
120
100
110
90
80
PI-5884-052510
Not Compensated
Compensated
相关PDF资料 |
PDF描述 |
|---|---|
| PFS758HG | 2.62 A SWITCHING CONTROLLER, 70 kHz SWITCHING FREQ-MAX, PZIP16 |
| PFS759HG | 2.94 A SWITCHING CONTROLLER, 70 kHz SWITCHING FREQ-MAX, PZIP16 |
| PGA112AIDGSR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| PGA113AIDGSRG4 | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| PGA112AIDGSRG4 | SPECIALTY ANALOG CIRCUIT, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PFS764HG | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Combined Two-Switch Forward and Flyback Power Supply Controllers with Integrated High Voltage MOSFETs |
| PFS7S 230/9V | 制造商:Aten International 功能描述:Bulk |
| PFS7S 230V/11 | 制造商:Aten International 功能描述: |
| PFS7S 230V/17V | 制造商:Aten International 功能描述: |
| PFS7S 230V/23 | 制造商:Aten International 功能描述: |
发布紧急采购，3分钟左右您将得到回复。