参数资料
型号: PG001M
厂商: Allegro MicroSystems, Inc.
英文描述: PARALLEL-TO-SERIAL DATA CONVERTER
中文描述: 并行到串行数据转换器
文件页数: 7/12页
文件大小: 179K
代理商: PG001M
PG001M
PARALLEL-TO-SERIAL
DATA CONVERTER
Figure 3 — Typical 'Integrated' Microstepping System
REF/ENABLE
CLOCK
STROBE
SERIAL DATA
SERIAL DATA
Dwg. EK-014A
1
MODE SELECT
MONITOR
CCW/CW
RESET
VECTOR CONTROL
MODE SELECT2
μ
P
CLOCKIN
S
o
S
RS
RS
GB
GA
P
GND
A
A
B
B
VDD
A
A
B
A
B
A
B
OUT
VBB
CONTROL SUPPLY
B
+5 V
A
B
After the RESET pulse, the first (two) full-steps in the
microstepping sequence, MS
1
is switched LOW and the
control IC shifts into the 1/4-step mode. It becomes very
apparent that any microstepping directly from a
μ
P to the
SLA7042/44M module 'burdens' the
μ
P, complicates the
software, and might entail a 'dedicated' microcontroller in
many motion-control systems.
The PG001M controller IC precludes loading a
μ
P
with direct serial-data signals to the power multi-chip
module. Because the step motor is updated at eight times
the step rate, this CMOS IC both simplifies software and
eliminates loading a system microprocessor with 'house-
keeping' control of step motors.
As illustrated in figures 4 and 5, the controller IC
eliminates the requirement to program the system for the
various modes of operation and the continual updating of
the serial-data signals to the power multi-chip module.
NOTE — In figures 4 and 5, the clock frequency is
constant during the few steps of operation that are shown
and half-step operation is not included.
Depicted in figure 4 are the 'front-end' I/O signals
(from RESET to VECTOR CONTROL), converted signals
from the controller IC to the microstepping power module
(CLOCK
OUT
, SERIAL DATA
A
, SERIAL DATA
B
, and
STROBE), plus the MONITOR (readback) to the
microcontroller. Finally, the power multi-chip module
current ratios are illustrated (OUT
A
and OUT
B
).
As shown, initially the counter is reset, and then the
motor is operating in quarter-step mode; then MS
2
is
switched while MO is LOW. The two steps following are
full-step (100% torque vector). The final (fourth quadrant)
portion of figure 4 is the maximum (141%) torque mode,
after VECTOR CONTROL has been switched from LOW
to HIGH. Three of the five operational modes are shown,
and none require the
μ
P to continually update the clock,
serial-data input, or strobe to the SLA7042/44M module.
The microstepping operation is illustrated in figure 5.
Initially the counter is reset, and with both MODE SE-
LECTs HIGH the controller is furnishing clock, serial
data, and strobe logic signals for 1/8
th
step increments.
相关PDF资料
PDF描述
PG1113F 1113F Series, Right Angle SMT LED
PG1157 TRANSISTOR | BJT | NPN | 60V V(BR)CEO | 5A I(C) | TO-5
PG1158 TRANSISTOR | BJT | NPN | 80V V(BR)CEO | 5A I(C) | TO-5
PG1159 TRANSISTOR | BJT | NPN | 100V V(BR)CEO | 5A I(C) | TO-5
PG1160 TRANSISTOR | BJT | NPN | 60V V(BR)CEO | 5A I(C) | TO-5
相关代理商/技术参数
参数描述
PG001M_10 制造商:SANKEN 制造商全称:Sanken electric 功能描述:Serial Signal Generator ICs for SLA7042M and SLA7044M
PG0035 功能描述:固定电感器 GAPPED TOROID IND RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
PG0036 功能描述:固定电感器 GAPPED TOROID IND RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
PG0036NL 功能描述:固定电感器 INDUCTOR GAPPED TOROID RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
PG0040.102T 制造商:Pulse 功能描述:IND PWR SHLD 1UH 20% 100KHZ 1.2A - Tape and Reel 制造商:Pulse Electronics Corporation 功能描述:Ind Power Shielded Wirewound 1uH 20% 100KHz 1.2A T/R