参数资料
型号: PIC12LF1501-I/MF
厂商: Microchip Technology
文件页数: 23/33页
文件大小: 0K
描述: IC MCU 8BIT 1.75KB FLASH 8-DFN
标准包装: 120
系列: PIC® 12F
核心处理器: PIC
芯体尺寸: 8-位
速度: 20MHz
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 5
程序存储器容量: 1.75KB(1K x 14)
程序存储器类型: 闪存
RAM 容量: 64 x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 3.6 V
数据转换器: A/D 4x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 8-VDFN 裸露焊盘
包装: 管件
PIC18F1220/1320
DS39605F-page 28
2007 Microchip Technology Inc.
3.4.4
EXIT TO IDLE MODE
An exit from a power managed Run mode to its
corresponding Idle mode is executed by setting the
IDLEN bit and executing a SLEEP instruction. The CPU
is halted at the beginning of the instruction following the
SLEEP
instruction. There are no changes to any of the
clock source status bits (OSTS, IOFS or T1RUN).
While the CPU is halted, the peripherals continue to be
clocked from the previously selected clock source.
3.4.5
EXIT TO SLEEP MODE
An exit from a power managed Run mode to Sleep
mode is executed by clearing the IDLEN and
SCS1:SCS0 bits and executing a SLEEP instruction.
The code is no different than the method used to invoke
Sleep mode from the normal operating (full power)
mode.
The primary clock and internal oscillator block are
disabled. The INTRC will continue to operate if the
WDT is enabled. The Timer1 oscillator will continue to
run, if enabled in the T1CON register (Register 12-1).
All clock source status bits are cleared (OSTS, IOFS
and T1RUN).
3.5
Wake from Power Managed Modes
An exit from any of the power managed modes is trig-
gered by an interrupt, a Reset or a WDT time-out. This
section discusses the triggers that cause exits from
power managed modes. The clocking subsystem
actions are discussed in each of the power managed
modes (see Sections 3.2 through 3.4).
Device behavior during Low-Power mode exits is
summarized in Table 3-3.
3.5.1
EXIT BY INTERRUPT
Any of the available interrupt sources can cause the
device to exit a power managed mode and resume full
power operation. To enable this functionality, an inter-
rupt source must be enabled by setting its enable bit in
one of the INTCON or PIE registers. The exit sequence
is initiated when the corresponding interrupt flag bit is
set. On all exits from Low-Power mode by interrupt,
code execution branches to the interrupt vector if the
GIE/GIEH bit (INTCON<7>) is set. Otherwise, code
execution continues or resumes without branching
Note:
If application code is timing sensitive, it
should wait for the OSTS bit to become set
before continuing. Use the interval during
the low-power exit sequence (before
OSTS is set) to perform timing insensitive
“housekeeping” tasks.
相关PDF资料
PDF描述
PIC14000-04I/SO IC MCU OTP 4KX14 A/D 28SOIC
PIC16C432T-I/SS IC MCU CMOS 8BIT 20MHZ 2K 20SSOP
PIC16C433-I/SO IC MCU CMOS 8BIT 10MHZ 2K 18SOIC
PIC16C505-20I/SL IC MCU OTP 1KX12 14SOIC
PIC16C558-04/SO IC MCU OTP 2KX14 18SOIC
相关代理商/技术参数
参数描述
PIC12LF1501T-I/MC 功能描述:8位微控制器 -MCU 1.75KB FL 64B RAM 6 IO 10-bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12LF1501T-I/MF 功能描述:8位微控制器 -MCU 1.75KB Fl 64B R 10-bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12LF1501T-I/MS 功能描述:8位微控制器 -MCU 1.75KB FL 64BR 6 I/O CLC NCO 10-bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12LF1501T-I/SN 功能描述:8位微控制器 -MCU 1.75KB FL 64BR 6 I/O CLC NCO 10-bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12LF1552-E/MS 功能描述:8位微控制器 -MCU 3.5 KB Flash, 256 bytes RAM, 16 MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT