- 您现在的位置：买卖IC网 > PDF目录1962 > PIC12LF1501-I/MF (Microchip Technology)IC MCU 8BIT 1.75KB FLASH 8-DFN PDF资料下载
参数资料
| 型号： | PIC12LF1501-I/MF |
| 厂商： | Microchip Technology |
| 文件页数： | 25/33页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8BIT 1.75KB FLASH 8-DFN |
| 标准包装： | 120 |
| 系列： | PIC® 12F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 20MHz |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 5 |
| 程序存储器容量： | 1.75KB（1K x 14） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 64 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.8 V ~ 3.6 V |
| 数据转换器： | A/D 4x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-VDFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页
PIC18F1220/1320
DS39605F-page 30
2007 Microchip Technology Inc.
3.5.2
EXIT BY RESET
Normally, the device is held in Reset by the Oscillator
Start-up Timer (OST) until the primary clock (defined in
Configuration Register 1H) becomes ready. At that
time, the OSTS bit is set and the device begins
executing code.
Code execution can begin before the primary clock
becomes ready. If either the Two-Speed Start-up (see
Section 19.3 “Two-Speed Start-up”) or Fail-Safe
Clock Monitor (see Section 19.4 “Fail-Safe Clock
Monitor”) are enabled in Configuration Register 1H,
the device may begin execution as soon as the Reset
source has cleared. Execution is clocked by the
INTOSC multiplexer driven by the internal oscillator
block. Since the OSCCON register is cleared following
all Resets, the INTRC clock source is selected. A
higher speed clock may be selected by modifying the
IRCF bits in the OSCCON register. Execution is
clocked by the internal oscillator block until either the
primary clock becomes ready, or a power managed
mode is entered before the primary clock becomes
ready; the primary clock is then shut down.
3.5.3
EXIT BY WDT TIME-OUT
A WDT time-out will cause different actions, depending
on which power managed mode the device is in when
the time-out occurs.
If the device is not executing code (all Idle modes and
Sleep mode), the time-out will result in a wake from the
If the device is executing code (all Run modes), the
time-out will result in a WDT Reset (see Section 19.2
The WDT timer and postscaler are cleared by
executing a SLEEP or CLRWDT instruction, the loss of a
currently selected clock source (if the Fail-Safe Clock
Monitor is enabled) and modifying the IRCF bits in the
OSCCON register if the internal oscillator block is the
system clock source.
3.5.4
EXIT WITHOUT AN OSCILLATOR
START-UP DELAY
Certain exits from power managed modes do not
invoke the OST at all. These are:
PRI_IDLE mode, where the primary clock source
is not stopped; or
the primary clock source is not any of LP, XT, HS
or HSPLL modes.
In these cases, the primary clock source either does
not require an oscillator start-up delay, since it is
already running (PRI_IDLE), or normally does not
require an oscillator start-up delay (RC, EC and INTIO
Oscillator modes).
However, a fixed delay (approximately 10
μs) following
the wake event is required when leaving Sleep and Idle
modes. This delay is required for the CPU to prepare
for execution. Instruction execution resumes on the first
clock cycle following this delay.
3.6
INTOSC Frequency Drift
The factory calibrates the internal oscillator block
output (INTOSC) for 8 MHz (see Table 22-6). However,
this frequency may drift as VDD or temperature
changes, which can affect the controller operation in a
variety of ways.
It is possible to adjust the INTOSC frequency by
modifying
the
value
in
the
OSCTUNE
register
(Register 2-1). This has the side effect that the INTRC
clock source frequency is also affected. However, the
features that use the INTRC source often do not require
an exact frequency. These features include the Fail-Safe
Clock Monitor, the Watchdog Timer and the RC_RUN/
RC_IDLE modes when the INTRC clock source is
selected.
Being able to adjust the INTOSC requires knowing
when an adjustment is required, in which direction it
should be made and in some cases, how large a
change is needed. Three examples follow but other
techniques may be used.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC14000-04I/SO | IC MCU OTP 4KX14 A/D 28SOIC |
| PIC16C432T-I/SS | IC MCU CMOS 8BIT 20MHZ 2K 20SSOP |
| PIC16C433-I/SO | IC MCU CMOS 8BIT 10MHZ 2K 18SOIC |
| PIC16C505-20I/SL | IC MCU OTP 1KX12 14SOIC |
| PIC16C558-04/SO | IC MCU OTP 2KX14 18SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC12LF1501T-I/MC | 功能描述:8位微控制器 -MCU 1.75KB FL 64B RAM 6 IO 10-bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC12LF1501T-I/MF | 功能描述:8位微控制器 -MCU 1.75KB Fl 64B R 10-bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC12LF1501T-I/MS | 功能描述:8位微控制器 -MCU 1.75KB FL 64BR 6 I/O CLC NCO 10-bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC12LF1501T-I/SN | 功能描述:8位微控制器 -MCU 1.75KB FL 64BR 6 I/O CLC NCO 10-bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC12LF1552-E/MS | 功能描述:8位微控制器 -MCU 3.5 KB Flash, 256 bytes RAM, 16 MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。