收藏本站
参数资料
型号： PIC14000-20/SO
厂商： Microchip Technology
文件页数： 107/153页
文件大小： 0K
描述： IC MCU OTP 4KX14 A/D 28SOIC
产品培训模块： Asynchronous Stimulus
标准包装： 27
系列： PIC® 14
核心处理器： PIC
芯体尺寸： 8-位
速度： 20MHz
连通性： I²C
外围设备： POR，温度传感器，WDT
输入/输出数： 20
程序存储器容量： 7KB（4K x 14）
程序存储器类型： OTP
RAM 容量： 192 x 8
电压 - 电源 (Vcc/Vdd)： 2.7 V ~ 6 V
数据转换器： 斜率 A/D
振荡器型： 内部
工作温度： 0°C ~ 70°C
封装/外壳： 28-SOIC（0.295"，7.50mm 宽）
包装： 管件
1996 Microchip Technology Inc.
Preliminary
DS40122B-page 57
PIC14000
8.0
ANALOG MODULES FOR A/D
CONVERSION
8.1
Overview
The PIC14000 includes analog components to create a
slope A/D converter including:
Comparator
4-bit programmable current source
16-channel analog mux
16-bit timer with capture register
Each channel is converted independently by means of
a slope conversion method using a single precision
comparator. The programmable current source feeds
an external 0.1
F (nominal) capacitor to generate the
ramp voltage used in the conversion.
8.2
Conversion Process
These are the steps to perform data conversion:
Clear REFOFF (SLPCON<5>) and ADOFF
(SLPCON<0>) bits to enable the A/D module.
Initialize ADCON1<7:4> to initialize the program-
mable current source.
Set ADRST (ADCON0<1>), for a minimum of 200
s to stop the timer and fully discharge the ramp
capacitor to ground.
The A/D timer (ADTMR) increments from 0000h
to FFFFh and must be initialized before each con-
version.
To start a conversion, clear ADRST through soft-
ware, it will allow the timer to begin counting and
the ramp capacitor to begin charging.
When the ramp voltage exceeds the analog input,
the comparator output changes from high to low.
This transition causes a capture event and copies
the current A/D timer value into the 16-bit capture
register.
An interrupt is generated to the CPU if enabled.
Note:
The A/D timer continues to run following a
capture event.
The maximum A/D timer count is 65,536. It can be
clocked by the on-chip or external oscillator. At a 4 MHz
oscillation frequency, the maximum conversion time is
16.38 ms for a full count. A typical conversion should
complete before full-count is reached. A timer overow
ag is set once the timer rolls over (FFFFh to 0000h),
and an interrupt is sent to the CPU, if enabled.
End-user calibration is simplied or eliminated by mak-
ing use of the on-chip EPROM. Internal component val-
ues are measured at factory nal test and stored in the
memory for use by the application rmware.
Periodic conversion cycles should be performed on the
bandgap
and
slope
references
(described
in
Section 9.0) to compensate for A/D component drift.
Measurements for the reference voltage count are
equated to the voltage value stored into EPROM during
calibration. All other channel measurements are
compensated for by ratioing the actual count with the
bandgap count and multiplying by the bandgap voltage
value stored in EPROM. Since all measurements are
relative to the reference, offset voltages inherent in the
comparator are cancelled out. See AN624, “PIC14000
A/D Theory and Implementation” for further details of
A/D operation.
The analog components used in the conversion and
the A/D timer can be disabled during idle periods for
maximum power savings. Power-saving can be
achieved
via
software
and/or
hardware
control
(Section 10.8).
8.3
A/D Timer (ADTMR) Module
The A/D timer (ADTMR) is comprised of a 16-bit up
timer, which is incremented every oscillator cycle.
ADTMR is reset to 0000h by a power-up reset; other-
wise the software must initialize it after each conver-
sion. A separate 16-bit capture register (ADCAP) is
used to capture the ADTMR count if an A/D capture
event occurs (see below). Both the A/D timer and cap-
ture register are readable and writable. The low byte of
the A/D timer (ADTMRL) is accessed at location 0Eh
while the high byte (ADTMRH) is accessed at location
0Fh. Similarly, the low byte of the A/D capture register
(ADCAP) is accessed at location 15h, and the high byte
is located at 16h.
This document was created with FrameMaker404
相关PDF资料
PDF描述
VE-J43-IX-F3 CONVERTER MOD DC/DC 24V 75W
PIC16F877-04E/PQ IC MCU FLASH 8KX14 EE 44-MQFP
PIC16F877-20I/PQ IC MCU FLASH 8KX14 EE 44-MQFP
PIC16LC76-04/SP IC MCU OTP 8KX14 A/D PWM 28DIP
DG9461DV-T1-E3 IC SWITCH LV SPDT 6TSOP
相关代理商/技术参数
参数描述
PIC14000T-04/SO 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC14000T-04/SS 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC14000T-04I/SO 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC14000T-04I/SS 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC14000T-20/SO 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*