参数资料
型号: PIC16C433T-I/SO
厂商: Microchip Technology
文件页数: 84/126页
文件大小: 0K
描述: IC MCU CMOS 8BIT 10MHZ 2K 18SOIC
标准包装: 1,100
系列: PIC® 16C
核心处理器: PIC
芯体尺寸: 8-位
速度: 10MHz
连通性: LIN(本地互连网络)
外围设备: POR,WDT
输入/输出数: 5
程序存储器容量: 3.5KB(2K x 14)
程序存储器类型: OTP
RAM 容量: 128 x 8
电压 - 电源 (Vcc/Vdd): 4.5 V ~ 5.5 V
数据转换器: A/D 4x8b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 18-SOIC(0.295",7.50mm 宽)
包装: 带卷 (TR)
60
4378C–AVR–09/08
AT90PWM1
If PORTxn is written logic one when the pin is configured as an output pin, the port pin is driven
high (one). If PORTxn is written logic zero when the pin is configured as an output pin, the port
pin is driven low (zero).
11.2.2
Toggling the Pin
Writing a logic one to PINxn toggles the value of PORTxn, independent on the value of DDRxn.
Note that the SBI instruction can be used to toggle one single bit in a port.
11.2.3
Switching Between Input and Output
When switching between tri-state ({DDxn, PORTxn} = 0b00) and output high ({DDxn, PORTxn}
= 0b11), an intermediate state with either pull-up enabled {DDxn, PORTxn} = 0b01) or output
low ({DDxn, PORTxn} = 0b10) must occur. Normally, the pull-up enabled state is fully accept-
able, as a high-impedant environment will not notice the difference between a strong high driver
and a pull-up. If this is not the case, the PUD bit in the MCUCR Register can be set to disable all
pull-ups in all ports.
Switching between input with pull-up and output low generates the same problem. The user
must use either the tri-state ({DDxn, PORTxn} = 0b00) or the output high state ({DDxn, PORTxn}
= 0b11) as an intermediate step.
Table 7 summarizes the control signals for the pin value.
11.2.4
Reading the Pin Value
Independent of the setting of Data Direction bit DDxn, the port pin can be read through the
PINxn Register bit. As shown in Figure 11-2, the PINxn Register bit and the preceding latch con-
stitute a synchronizer. This is needed to avoid metastability if the physical pin changes value
near the edge of the internal clock, but it also introduces a delay. Figure 11-3 shows a timing dia-
gram of the synchronization when reading an externally applied pin value. The maximum and
minimum propagation delays are denoted tpd,max and tpd,min respectively.
Table 7. Port Pin Configurations
DDxn
PORTxn
PUD
(in MCUCR)
I/O
Pull-up
Comment
0
X
Input
No
Default configuration after Reset.
Tri-state (Hi-Z)
0
1
0
Input
Yes
Pxn will source current if ext. pulled low.
0
1
Input
No
Tri-state (Hi-Z)
1
0
X
Output
No
Output Low (Sink)
1
X
Output
No
Output High (Source)
相关PDF资料
PDF描述
PIC16C773T-E/SO IC MCU OTP 4KX14 A/D PWM 28SOIC
PIC16CE623T-30/SO IC MCU OTP 512X14 EE COMP 18SOIC
PIC16F1825-E/ML MCU PIC 14K FLASH 1K RAM 16QFN
PIC16F1828-I/SO IC PIC MCU 8BIT 14KB FLSH 20SOIC
PIC16F688-I/SL IC PIC MCU FLASH 4KX14 14SOIC
相关代理商/技术参数
参数描述
PIC16C505/JW 功能描述:8位微控制器 -MCU 1.5KB 72 RAM 12 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C505-04/P 功能描述:8位微控制器 -MCU 1.5KB 72 RAM 12 I/O 4MHz PDIP14 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C505-04/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU (TUBE 30) 16C505 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU 16C505 DIP14
PIC16C505-04/SL 功能描述:8位微控制器 -MCU 1.5KB 72 RAM 12 I/O 4MHz SOIC14 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C505-04/SL 制造商:Microchip Technology Inc 功能描述:8BIT CMOS MCU SMD 16C505 SOIC14