参数资料
型号: PIC16F1826-E/SS
厂商: Microchip Technology
文件页数: 36/109页
文件大小: 0K
描述: MCU PIC 8BIT 2K FLASH 20-SSOP
标准包装: 67
系列: PIC® XLP™ mTouch™ 16F
核心处理器: PIC
芯体尺寸: 8-位
速度: 32MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 16
程序存储器容量: 3.5KB(2K x 14)
程序存储器类型: 闪存
EEPROM 大小: 256 x 8
RAM 容量: 256 x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 5.5 V
数据转换器: A/D 12x10b
振荡器型: 内部
工作温度: -40°C ~ 125°C
封装/外壳: 20-SSOP(0.209",5.30mm 宽)
包装: 管件
190
2570N–AVR–05/11
ATmega325/3250/645/6450
Figure 21-4. Two-wire Mode Operation, Simplified Diagram
Figure 21-4 shows two USI units operating in Two-wire mode, one as Master and one as Slave.
It is only the physical layer that is shown since the system operation is highly dependent of the
communication scheme used. The main differences between the Master and Slave operation at
this level, is the serial clock generation which is always done by the Master, and only the Slave
uses the clock control unit. Clock generation must be implemented in software, but the shift
operation is done automatically by both devices. Note that only clocking on negative edge for
shifting data is of practical use in this mode. The slave can insert wait states at start or end of
transfer by forcing the SCL clock low. This means that the Master must always check if the SCL
line was actually released after it has generated a positive edge.
Since the clock also increments the counter, a counter overflow can be used to indicate that the
transfer is completed. The clock is generated by the master by toggling the USCK pin via the
PORT Register.
The data direction is not given by the physical layer. A protocol, like the one used by the TWI-
bus, must be implemented to control the data flow.
Figure 21-5. Two-wire Mode, Typical Timing Diagram
Referring to the timing diagram (Figure 21-5.), a bus transfer involves the following steps:
MASTER
SLAVE
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
SDA
SCL
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
Two-wire Clock
Control Unit
HOLD
SCL
PORTxn
SDA
SCL
VCC
P
S
ADDRESS
1 - 7
8
9
R/W
ACK
1 - 8
9
DATA
ACK
1 - 8
9
DATA
SDA
SCL
A B
D
E
C
F
相关PDF资料
PDF描述
V72A15C400BF3 CONVERTER MOD DC/DC 15V 400W
V72A15C400BF2 CONVERTER MOD DC/DC 15V 400W
PIC16F1826-E/SO MCU PIC 8BIT 2K FLASH 18-SOIC
V72A15C400BF CONVERTER MOD DC/DC 15V 400W
V72A15C400BL3 CONVERTER MOD DC/DC 15V 400W
相关代理商/技术参数
参数描述
PIC16F1826-I/ML 功能描述:8位微控制器 -MCU 3.5KB Flash 256 byte 32 MHz Int. Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1826-I/MQ 功能描述:8位微控制器 -MCU 3.5KB Flash 256 byte 32 MHz Int. Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1826-I/MV 功能描述:8位微控制器 -MCU 3.5KB Flash 256 RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1826-I/P 功能描述:8位微控制器 -MCU 3.5KB Flash 256 byte 32 MHz Int. Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1826-I/SO 功能描述:8位微控制器 -MCU 3.5KB Flash 256 byte 32 MHz Int. Osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT