- 您现在的位置：买卖IC网 > PDF目录3886 > PIC16LCE624-04E/P (Microchip Technology)IC MCU CMOS 1K OTP W/EEPRM 18DIP PDF资料下载
参数资料
| 型号： | PIC16LCE624-04E/P |
| 厂商： | Microchip Technology |
| 文件页数： | 9/100页 |
| 文件大小： | 0K |
| 描述： | IC MCU CMOS 1K OTP W/EEPRM 18DIP |
| 标准包装： | 25 |
| 系列： | PIC® 16C |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 4MHz |
| 外围设备： | 欠压检测/复位，POR，WDT |
| 输入/输出数： | 13 |
| 程序存储器容量： | 1.75KB（1K x 14） |
| 程序存储器类型： | OTP |
| EEPROM 大小： | 128 x 8 |
| RAM 容量： | 96 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.5 V ~ 5.5 V |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 18-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
ENC424J600/624J600
DS39935C-page 106
2010 Microchip Technology Inc.
11.2
Manual and Automatic Flow
Control
11.2.1
MANUAL FLOW CONTROL
Manual flow control is enabled by default on device
power-up and whenever the AUTOFC bit (ECON2<7>)
is cleared. Setting AUTOFC disables manual flow
control.
To begin manual flow control in Full-Duplex mode, set
FCOP<1:0> to one of the following combinations:
Idle (‘00’): Flow control is disabled or Idle.
Single Pause (‘01’): Transmit one pause frame for
the time indicated in EPAUS; automatically
returns to the Idle state (‘00’).
Continuous Pause (‘10’): Periodically transmit
pause frames using the value indicated in EPAUS
for an indefinite time; must be terminated using
End (‘11’).
End (‘11’): Transmit one pause frame with a timer
of 0000h, then return to the Idle state (‘00’).
In Half-Duplex mode, set FCOP<1:0> to ‘10’ to begin
flow control and to ‘00’ to terminate flow control.
11.2.2
AUTOMATIC FLOW CONTROL
When the AUTOFC bit is set, the ENCX24J600 auto-
matically initiates flow control operation when the
amount of data in the receive buffer crosses an upper
threshold value. Flow control automatically terminates
once the amount of pending data shrinks below a lower
threshold. These thresholds, or “watermarks”, are
determined by the upper and lower bytes (respectively)
of the Receive Watermark register, ERXWM. These
thresholds represent 96-byte blocks.
For example, setting the RXFWM bits to 20h and the
RXEWM bits to 10h initiates flow control when more
than 3072 bytes of data are present in the buffer. Flow
control terminates when fewer than 1536 bytes of data
are in the buffer.
In Automatic mode, the value of FCOP<1:0> is
controlled by the device and must not be changed by
software. These bits, however, can be used as status
bits to determine what state the automatic flow control
engine is in. A value of ‘10’ indicates flow control is
active, while ‘00’ indicates that flow control is Idle.
To use automatic flow control:
1.
Set the EPAUS register to indicate how many
pause quanta should be specified in each
control frame. It is recommended that the default
value be used.
2.
Set RXFWM<7:0> (ERXWM<15:8>) to indicate
when flow control is to begin. When this number
of 96-byte blocks is consumed in the receive
buffer, the device considers its receive buffer to
be full and initiates flow control. Use the default
value of 16 if the full threshold is to be set at
1536 bytes.
3.
Set RXEWM<7:0> (ERXWM<7:0>) to indicate
when flow control is to end. When the number of
occupied 96-byte blocks falls below this level,
the device considers its receive buffer to be
empty enough to receive more data. Use the
default value of 15 if the empty threshold is to be
set at 1440 bytes.
4.
Set AUTOFC (ECON2<7>) to give control of the
FCOP<1:0> bits to the automatic flow control
hardware.
Note:
When flow control is used in conjunction
with auto-negotiation, also set the ADPAUS
bits (PHANA<11:10>) to ‘01’ during initial-
ization. See Section 12.0 “Speed/Duplex
for
more information.
Note:
Setting RXFWM to be equal to RXEWM
(i.e., no hysteresis between full and empty)
is not permitted. For automatic flow control
to operate correctly, RXEWM must always
be at least one less than RXFWM, implying
at least 96 bytes of hysteresis.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16F689-I/SS | IC PIC MCU FLASH 4KX14 20SSOP |
| PIC16C54C-04I/SO | IC MCU OTP 512X12 18SOIC |
| PIC16C54C-04/SO | IC MCU OTP 512X12 18SOIC |
| PIC16F722-I/ML | IC PIC MCU FLASH 2KX14 28-QFN |
| PIC16LCE623T-04I/SO | IC MCU CMOS.5K OTP W/EEPRM18SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC16LCE624-04I/P | 功能描述:8位微控制器 -MCU 1.75KB 96 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16LCE624-04I/SO | 功能描述:8位微控制器 -MCU 1.75KB 96 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16LCE624-04I/SS | 功能描述:8位微控制器 -MCU 1.75KB 96 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16LCE624T-04/SO | 功能描述:8位微控制器 -MCU 1.75KB 96 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC16LCE624T-04/SS | 功能描述:8位微控制器 -MCU 1.75KB 96 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。