参数资料
型号: PIC18F66J10-I/PT
厂商: Microchip Technology
文件页数: 26/44页
文件大小: 0K
描述: IC PIC MCU FLASH 32KX16 64TQFP
产品培训模块: Asynchronous Stimulus
PIC18 J Series MCU Overview
8-bit PIC® Microcontroller Portfolio
标准包装: 160
系列: PIC® 18F
核心处理器: PIC
芯体尺寸: 8-位
速度: 40MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 50
程序存储器容量: 64KB(32K x 16)
程序存储器类型: 闪存
RAM 容量: 2K x 8
电压 - 电源 (Vcc/Vdd): 2 V ~ 3.6 V
数据转换器: A/D 11x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 64-TQFP
包装: 托盘
产品目录页面: 644 (CN2011-ZH PDF)
配用: MA180015-ND - MODULE PLUG-IN 18F87J10 FOR HPC
AC162062-ND - HEADER INTRFC MPLAB ICD2 64/80P
AC164327-ND - MODULE SKT FOR 64TQFP
PIC18F87J10 FAMILY
DS39663F-page 30
2009 Microchip Technology Inc.
2.6
External Oscillator Pins
Many microcontrollers have options for at least two
oscillators: a high-frequency primary oscillator and a
low-frequency
secondary
oscillator
(refer
to
The oscillator circuit should be placed on the same
side of the board as the device. Place the oscillator
circuit close to the respective oscillator pins with no
more than 0.5 inch (12 mm) between the circuit
components and the pins. The load capacitors should
be placed next to the oscillator itself, on the same side
of the board.
Use a grounded copper pour around the oscillator
circuit to isolate it from surrounding circuits. The
grounded copper pour should be routed directly to the
MCU ground. Do not run any signal traces or power
traces inside the ground pour. Also, if using a
two-sided board, avoid any traces on the other side of
the board where the crystal is placed. A suggested
layout is shown in Figure 2-4.
For additional information and design guidance on
oscillator circuits, please refer to these Microchip
Application Notes, available at the corporate web site
(www.microchip.com):
AN826, “Crystal Oscillator Basics and Crystal
Selection for rfPIC and PICmicro Devices”
AN849, “Basic PICmicro Oscillator Design”
AN943, “Practical PICmicro Oscillator Analysis
and Design”
AN949, “Making Your Oscillator Work”
FIGURE 2-4:
SUGGESTED PLACEMENT
OF THE OSCILLATOR
CIRCUIT
2.7
Unused I/Os
Unused I/O pins should be configured as outputs and
driven to a logic low state. Alternatively, connect a 1 k
to 10 k resistor to VSS on unused pins and drive the
output to logic low.
13
Main Oscillator
Guard Ring
Guard Trace
Secondary
Oscillator
14
15
16
17
18
19
20
相关PDF资料
PDF描述
PIC18F26J11-I/SO IC PIC MCU FLASH 64K 2V 28-SOIC
PIC24FJ32GA004-I/ML IC PIC MCU FLASH 32KB 44QFN
SFW18S-6STME1 SFW18S-6STME1-FFC/FPC CONN
SLW22R-5C7 SLW22R-5C7-FFC/FPC CONN
HFW4R-1STE1 HFW4R-1STE1-FFC/FPC CONN
相关代理商/技术参数
参数描述
PIC18F66J10T-I/PT 功能描述:8位微控制器 -MCU 64 KB FL 2 KB RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F66J11-I/PT 功能描述:8位微控制器 -MCU 64KB FL 3936 bytes RAM 10 MIPS 51 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F66J11T-I/PT 功能描述:8位微控制器 -MCU 64KB Flash 3936 bytesRAM 51I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F66J15-I/PT 功能描述:8位微控制器 -MCU 96 KB FL 4 KB RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F66J15T-I/PT 功能描述:8位微控制器 -MCU 96 KB FL 4 KB RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT