- 您现在的位置：买卖IC网 > PDF目录3850 > PIC18F86J11-I/PT (Microchip Technology)IC PIC MCU FLASH 32KX16 80TQFP PDF资料下载
参数资料
| 型号： | PIC18F86J11-I/PT |
| 厂商： | Microchip Technology |
| 文件页数： | 49/107页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 32KX16 80TQFP |
| 产品培训模块： | Asynchronous Stimulus PIC18 J Series MCU Overview 8-bit PIC® Microcontroller Portfolio |
| 标准包装： | 119 |
| 系列： | PIC® 18F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 48MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，LVD，POR，PWM，WDT |
| 输入/输出数： | 68 |
| 程序存储器容量： | 64KB（32K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 3930 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2 V ~ 3.6 V |
| 数据转换器： | A/D 15x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 80-TQFP |
| 包装： | 托盘 |
| 产品目录页面： | 644 (CN2011-ZH PDF) |
| 配用： | AC162091-ND - HEADER MPLAB ICD2 18F87J11 64/80 MA180020-ND - MODULE PLUG-IN HPC EXPL 18F87J11 AC164328-ND - MODULE SKT FOR 80TQFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页当前第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页
PIC18F87J11 FAMILY
DS39778E-page 46
2007-2012 Microchip Technology Inc.
3.7
Effects of Power-Managed Modes
on the Various Clock Sources
When PRI_IDLE mode is selected, the designated pri-
mary oscillator continues to run without interruption.
For all other power-managed modes, the oscillator
using the OSC1 pin is disabled. The OSC1 pin (and
OSC2 pin if used by the oscillator) will stop oscillating.
In
secondary
clock
modes
(SEC_RUN
and
SEC_IDLE), the Timer1 oscillator is operating and
providing the device clock. The Timer1 oscillator may
also run in all power-managed modes if required to
clock Timer1 or Timer3.
In RC_RUN and RC_IDLE modes, the internal
oscillator provides the device clock source. The 31 kHz
INTRC output can be used directly to provide the clock
and may be enabled to support various special
features, regardless of the power-managed mode (see
through
for more
information on WDT, Fail-Safe Clock Monitor and
Two-Speed Start-up).
If the Sleep mode is selected, all clock sources are
stopped. Since all the transistor switching currents
have been stopped, Sleep mode achieves the lowest
current consumption of the device (only leakage
currents).
Enabling any on-chip feature that will operate during
Sleep will increase the current consumed during Sleep.
The INTRC is required to support WDT operation. The
Timer1 oscillator may be operating to support a Real-
Time Clock (RTC). Other features may be operating
that do not require a device clock source (i.e., MSSP
slave, PSP, INTx pins and others). Peripherals that
may add significant current consumption are listed in
3.8
Power-up Delays
Power-up delays are controlled by two timers, so that
no external Reset circuitry is required for most applica-
tions. The delays ensure that the device is kept in
Reset until the device power supply is stable under nor-
mal circumstances and the primary clock is operating
and stable. For additional information on power-up
delays, see Section 5.6 “Power-up Timer (PWRT)”.
The first timer is the Power-up Timer (PWRT), which
provides a fixed delay on power-up (Parameter 33,
Table 28-13); it is always enabled.
The second timer is the Oscillator Start-up Timer
(OST), intended to keep the chip in Reset until the
crystal oscillator is stable (HS modes). The OST does
this by counting 1024 oscillator cycles before allowing
the oscillator to clock the device.
Table 28-13), following POR, while the controller
becomes ready to execute instructions.
TABLE 3-3:
OSC1 AND OSC2 PIN STATES IN SLEEP MODE
Oscillator Mode
OSC1 Pin
OSC2 Pin
EC, ECPLL
Floating, pulled by external clock
At logic low (clock/4 output)
HS, HSPLL
Feedback inverter disabled at quiescent
voltage level
Feedback inverter disabled at quiescent
voltage level
INTOSC, INTPLL1/2
I/O pin, RA6, direction controlled by
TRISA<6>
I/O pin RA6, direction controlled by
TRISA<7>
Note:
See Section 5.0 “Reset” for time-outs due to Sleep and MCLR Reset.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC18F66J50-I/PT | IC PIC MCU FLASH 32KX16 64TQFP |
| PIC24FJ96GA006-I/PT | IC PIC MCU FLASH 96KB 64TQFP |
| PIC18F4321-I/ML | IC PIC MCU FLASH 4KX16 44QFN |
| PIC24FJ32GB002-I/SP | IC MCU 16BIT 32KB FLASH 28DIP |
| DSPIC33FJ16GP304-I/PT | IC DSPIC MCU/DSP 16K 44TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC18F86J11T-I/PT | 功能描述:8位微控制器 -MCU 64KB Flash 3936bytes RAM 67 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F86J15-I/PT | 功能描述:8位微控制器 -MCU 96 KB FL 4 KB RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F86J15T-I/PT | 功能描述:8位微控制器 -MCU 96 KB FL 4 KB RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F86J16-I/PT | 功能描述:8位微控制器 -MCU 96KB FL 3936b RAM 10 MIPS 67 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC18F86J16T-I/PT | 功能描述:8位微控制器 -MCU 96KB Flash 3936bytes RAM 67 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。