- 您现在的位置：买卖IC网 > PDF目录11547 > PIC24FJ16GA002T-I/SO (Microchip Technology)IC PIC MCU FLASH 16K 28SOIC PDF资料下载
参数资料
| 型号： | PIC24FJ16GA002T-I/SO |
| 厂商： | Microchip Technology |
| 文件页数： | 18/52页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 16K 28SOIC |
| 产品培训模块： | Graphics LCD System and PIC24 Interface Asynchronous Stimulus |
| 标准包装： | 1,600 |
| 系列： | PIC® 24F |
| 核心处理器： | PIC |
| 芯体尺寸： | 16-位 |
| 速度： | 32MHz |
| 连通性： | I²C，PMP，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，LVD，POR，PWM，WDT |
| 输入/输出数： | 21 |
| 程序存储器容量： | 16KB（5.5K x 24） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 4K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2 V ~ 3.6 V |
| 数据转换器： | A/D 10x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 包装： | 带卷 (TR) |
| 配用： | DM240011-ND - KIT STARTER MPLAB FOR PIC24F MCU AC162088-ND - HEADER MPLAB ICD2 24FJ64GA004 28 AC164339-ND - MODULE SKT FOR PM3 28SOIC DV164033-ND - KIT START EXPLORER 16 MPLAB ICD2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
2008 Microchip Technology Inc.
DS39768D-page 25
PIC24FJXXXGA0XX
3.10
Verify Code Memory and
Configuration Word
The verify step involves reading back the code memory
space and comparing it against the copy held in the
programmer’s buffer. The Configuration registers are
verified with the rest of the code.
The verify process is shown in the flowchart in
Figure 3-8. Memory reads occur a single byte at a time,
so two bytes must be read to compare against the word
in the programmer’s buffer. Refer to Section 3.8
“Reading Code Memory” for implementation details
of reading code memory.
FIGURE 3-8:
VERIFY CODE
MEMORY FLOW
3.11
Reading the Application ID Word
The Application ID Word is stored at address 8005BEh
in executive code memory. To read this memory
location, you must use the SIX control code to move
this program memory location to the VISI register.
Then, the REGOUT control code must be used to clock
the contents of the VISI register out of the device. The
corresponding control and instruction codes that must
be serially transmitted to the device to perform this
operation are shown in Table 3-10.
After the programmer has clocked out the Application
ID Word, it must be inspected. If the Application ID has
the value, BBh, the programming executive is resident
in memory and the device can be programmed using
the mechanism described in Section 4.0 “Device
Programming – Enhanced ICSP”. However, if the
Application ID has any other value, the programming
executive is not resident in memory; it must be loaded
to memory before the device can be programmed. The
procedure for loading the programming executive to
memory is described in Section 5.4 “Programming
3.12
Exiting ICSP Mode
Exiting Program/Verify mode is done by removing VIH
from MCLR, as shown in Figure 3-9. The only require-
ment for exit is that an interval, P16, should elapse
between the last clock and program signals on PGCx
and PGDx before removing VIH.
FIGURE 3-9:
EXITING ICSP MODE
Note:
Because
the
Configuration
registers
include the device code protection bit,
code memory should be verified immedi-
ately after writing if code protection is
enabled. This is because the device will
not be readable or verifiable if a device
Reset occurs after the code-protect bit in
CW1 has been cleared.
Read Low Byte
Read High Byte
Does
Word = Expect
Data?
Failure,
Report
Error
All
code memory
verified?
No
Yes
No
Set TBLPTR = 0
Start
Yes
Done
with Post-Increment
MCLR
P16
PGDx
PGD = Input
PGCx
VDD
VIH
P17
相关PDF资料 |
PDF描述 |
|---|---|
| GJM0335C1E1R8BB01D | CAP CER 1.8PF 25V NP0 0201 |
| GJM0335C1ER40BB01D | CAP CER 0.4PF 25V NP0 0201 |
| V375C12M75BF2 | CONVERTER MOD DC/DC 12V 75W |
| V375C12M75B3 | CONVERTER MOD DC/DC 12V 75W |
| GJM0335C1ER30BB01D | CAP CER 0.3PF 25V NP0 0201 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC24FJ16GA004 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:PIC24FJ64GA004 Family Silicon Errata and Data Sheet Clarification |
| PIC24FJ16GA004-E/ML | 功能描述:16位微控制器 - MCU 16B 16KB Flash I/O 16 MIPS nanoWatt RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| PIC24FJ16GA004-E/PT | 功能描述:16位微控制器 - MCU 16B 16KB Flash I/O 16 MIPS nanoWatt RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| PIC24FJ16GA004-EPT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:PIC24FJXXXGA0XX Flash Programming Specification |
| PIC24FJ16GA004-I/ML | 功能描述:16位微控制器 - MCU 16b Fam 16MIPS 16KB FL 4096b RAM 35 I/O RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。