- 您现在的位置：买卖IC网 > PDF目录98052 > PIM200AZ (LINEAGE POWER LLC) 1-OUTPUT 8 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PIM200AZ |
| 厂商： | LINEAGE POWER LLC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 8 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT PACKAGE-13 |
| 文件页数： | 3/18页 |
| 文件大小： | 346K |
| 代理商： | PIM200AZ |
Data Sheet
October 5, 2009
PIM200X Series; ATCA Board Power Input Modules
-38 to -75Vdc; 200W Input
LINEAGE POWER
11
The -48V_OUT bus may require a fuse
depending on the power and fusing
requirements of the DC/DC converter(s).
Input filtering of the DC/DC converter is
provided by C_FLTR close to the input pins
of the DC/DC converter(s); additional high
frequency decoupling ceramic capacitors
(0.01 to 0.1μF are strongly recommended for
improved EMI performance.
The maximum C_FLTR capacitance across
all the downstream DC/DC converters
should not exceed 220μF. The
recommended capacitor voltage rating
should be >/= 100Vdc.
The minimum C_FLTR capacitance (200μF)
recommendation is based on meeting the
EMI requirements. Based on end systems
test, the capacitance may be lowered if real
estate is an issue. As a minimum, 50 μF to
100 μF is strongly recommended to stabilize
the line impedance for proper startup of the
DC/DC converter. Refer to the DC/DC
converter’s data sheet for the recommended
capacitor.
(2) Holdup / Bulk Capacitor Output (72V_CAP)
This output provides the high voltage (nominal 72Vdc)
to charge the C_BULK capacitor(s) to allow the ATCA
board to meet the 5ms, 0Volts transient requirements.
The 72V_CAP connects to the +ve terminals
of the C_HLDP capacitors while the –ve
terminals of the C_HLDP connects to the -
48V_OUT bus.
Since the 72V_CAP output is regulated to
72Vdc (+3%/-5%) and the capacitors are off
line during normal operation, the capacitors
may be selected with voltage rating of >/=
80V to minimize the real estate on the board.
The C_HLDP capacitance is dependent on
the system power and the holdup time
requirements based on the following formula
9
.
1
/
}]
7
.
1
)
(
{
)
(
[
)
(
_
+
≥
ms
T
W
P
F
HLDP
C
holdup
out
μ
The capacitance tolerance (normally +20%)
should be added to the calculated value.
Bleed Resistor ( R_Bleed) : The PICMG 3.0
specifications requires a discharge
mechanism (e.g. bleed resistor) to discharge
the holdup/bulk capacitance to less than -
60Vdc and less than 20 joules within one
second of disconnection from the backplane.
This requirement is fulfilled by installing
R_Bleed resistor that is selected based on
the C_HLDP selected in the previous step.
The formula for selecting the resistor is :
)
(
_
/
485
.
5
)
(
_
F
HLDP
C
Bleed
R
≤
Ω
For 200W and 9.3 ms holdup requirements,
this results in a 3.9 Kohm resistor with 1W
rating.
Worst case power dissipation of R_Bleed
(=3.9Kohms) @ -36V is 0.33W.
The R_Bleed is connected across the
72V_CAP and VRTN_OUT pins of the
PIM200X.
(3) Management Power
(MGMT_PWR)
The MGMT_PWR output is an isolated secondary
voltage ( 3.3V for PIM200F or 5.0V for PIM200A)
referenced to LOGIC_GND that provides
8W(maximum) power to the IPM Controller for the
ATCA board or to the power up system controller for
other applications.
Per PICMG 3.0 Specs, the ATCA board
shall not consume more than 10W of input
power; this includes the standby power of
PIM200X (typically 1.7W) as well as all the
on board DC/DC power converters. It is the
responsibility of the board designer to insure
that this requirement is met prior to power-up
rights have been negotiated with the Shelf
Manager.
The management power is available even
when the input voltage is down to –36Vdc.
No additional output capacitors are required,
but a 22μF tantalum and a 0.01 to 0.1μF
ceramic capacitors are highly recommended
to contain the switching ripple and noise.
Higher output capacitance may be required
in case of large input line or output load
transient conditions.
(4) -48V Feed Loss or Open Fuse Alarm
(-48V_ALARM)
The -48V_ALARM output is an opto-isolated signal
internally referenced to the LOGIC_GND. The signal
is an open collector output that requires an external
pull up resistor. A 3.3K pull up resistor to 3.3V,
MGMT_PWR ( for PIM200F) should suffice. During
normal operation, the signal is LO (opto conducting).
During fault condition, the opto shall stop conducting
and the alarm signal shall assume a HI state.
Safety Considerations
For the system safety agency approval the power
module must be installed in compliance with the
spacing and separation requirements of the end-use
safety agency standards, i.e., UL 60950-1, CSA
相关PDF资料 |
PDF描述 |
|---|---|
| PIM200FZ | 1-OUTPUT 7.92 W DC-DC REG PWR SUPPLY MODULE |
| PIM300FZ | 2-OUTPUT 7.9 W DC-DC REG PWR SUPPLY MODULE |
| PIM300F6Z | 2-OUTPUT 7.9 W DC-DC REG PWR SUPPLY MODULE |
| PIP201-12M-3,518 | 200 A SWITCHING REGULATOR, PQCC68 |
| PIP201-12M | SPECIALTY ANALOG CIRCUIT, PQCC68 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIM200FZ | 功能描述:DC/DC转换器 2.4A in -38 to -75V out 3.3V 200W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PIM213 | 功能描述:AUTOMATION HAT (INDIVIDUAL) 制造商:pimoroni ltd 系列:- 零件状态:在售 平台:Raspberry Pi 类型:接口 功能:自动化 使用的 IC/零件:- 内容:板 标准包装:1 |
| PIM215 | 功能描述:PICADE HAT (HAT ONLY) 制造商:pimoroni ltd 系列:- 零件状态:在售 平台:Raspberry Pi 类型:接口 功能:弓形板 使用的 IC/零件:- 内容:板 标准包装:1 |
| PIM216 | 功能描述:MOTE PHAT 制造商:pimoroni ltd 系列:- 零件状态:在售 平台:Raspberry Pi 类型:电源管理 功能:LED 驱动器 使用的 IC/零件:- 内容:板 标准包装:1 |
| PIM221 | 功能描述:AUTOMATION PHAT 制造商:pimoroni ltd 系列:- 零件状态:在售 平台:Raspberry Pi 类型:接口 功能:自动化 使用的 IC/零件:- 内容:板 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。