- 您现在的位置：买卖IC网 > PDF目录69058 > PKR4117ASI (ERICSSON POWER MODULES AB) 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PKR4117ASI |
| 厂商： | ERICSSON POWER MODULES AB |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, SMD-18 |
| 文件页数： | 23/30页 |
| 文件大小： | 1444K |
| 代理商： | PKR4117ASI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页
Ericsson Internal
PRODUCT SPECIFICATION
3 (3)
Prepared (also subject responsible if other)
No.
EMINTAO
1/1301-BMR 640 1411+ Uen
Approved
Checked
Date
Rev
Reference
SEC/D (JULIA YOU)
(MICJOHN)
2007-09-18
F
Safety Specification
General information
Ericsson Power Modules DC/DC converters and DC/DC regulators are
designed in accordance with safety standards IEC/EN/UL60950, Safety
of Information Technology Equipment.
IEC/EN/UL60950 contains requirements to prevent injury or damage
due to the following hazards:
Electrical shock
Energy hazards
Fire
Mechanical and heat hazards
Radiation hazards
Chemical hazards
On-board DC-DC converters are defined as component power supplies.
As components they cannot fully comply with the provisions of any
Safety requirements without “Conditions of Acceptability”. It is the
responsibility of the installer to ensure that the final product housing
these components complies with the requirements of all applicable
Safety standards and Directives for the final product.
Component power supplies for general use should comply with the
requirements in IEC60950, EN60950 and UL60950 “Safety of
information technology equipment”.
There are other more product related standards, e.g. IEEE802.3af
“Ethernet LAN/MAN Data terminal equipment power”, and ETS300132-2
“Power supply interface at the input to telecommunications equipment;
part 2: DC”, but all of these standards are based on IEC/EN/UL60950
with regards to safety.
Ericsson Power Modules DC/DC converters and DC/DC regulators are
UL60950 recognized and certified in accordance with EN60950.
The flammability rating for all construction parts of the
products meets requirements for V-0 class material according to IEC
60695-11-10.
The products should be installed in the end-use equipment, in
accordance with the requirements of the ultimate application. Normally
the output of the DC/DC converter is considered as SELV (Safety Extra
Low Voltage) and the input source must be isolated by minimum Double
or Reinforced Insulation from the primary circuit (AC mains) in
accordance with IEC/EN/UL60950.
Isolated DC/DC converters
It is recommended that a slow blow fuse with a rating twice the
maximum input current per selected product be used at the input of
each DC/DC converter. If an input filter is used in the circuit the fuse
should be placed in front of the input filter.
In the rare event of a component problem in the input filter or in the
DC/DC converter that imposes a short circuit on the input source, this
fuse will provide the following functions:
Isolate the faulty DC/DC converter from the input power
source so as not to affect the operation of other parts of the
system.
Protect the distribution wiring from excessive current and
power loss thus preventing hazardous overheating.
The galvanic isolation is verified in an electric strength test.
The test voltage (Viso) between input and output is
1500 Vdc or 2250 Vdc for 60 seconds (refer to product specification).
Leakage current is less than 1 A at nominal input voltage.
24 V DC systems
The input voltage to the DC/DC converter is SELV (Safety
Extra Low Voltage) and the output remains SELV under normal and
abnormal operating conditions.
48 and 60 V DC systems
If the input voltage to Ericsson Power Modules DC/DC converter is 75
Vdc or less, then the output remains SELV (Safety Extra Low Voltage)
under normal and abnormal operating conditions.
Single fault testing in the input power supply circuit should be performed
with the DC/DC converter connected to demonstrate that the input
voltage does not exceed
75 Vdc.
If the input power source circuit is a DC power system, the source may
be treated as a TNV2 circuit and testing has demonstrated compliance
with SELV limits and isolation requirements equivalent to Basic
Insulation in accordance with IEC/EN/UL60950.
Non-isolated DC/DC regulators
The input voltage to the DC/DC regulator is SELV (Safety
Extra Low Voltage) and the output remains SELV under normal and
abnormal operating conditions.
E
PKR 4000A PI
DC/DC Converters, Input 36-75 V, 3 A / 15 W
EN/LZT 146 300 R5F April 2009
Ericsson AB
Technical Specication
3
相关PDF资料 |
PDF描述 |
|---|---|
| PKR4928ASI | 2-OUTPUT 9.5 W DC-DC REG PWR SUPPLY MODULE |
| PKR4221API | 2-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| PKR4910API | 1-OUTPUT 9.9 W DC-DC REG PWR SUPPLY MODULE |
| PKR4928API | 2-OUTPUT 9.5 W DC-DC REG PWR SUPPLY MODULE |
| PKR4117ASPBI | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PKR4117ASIA | 制造商:Ericsson 功能描述: |
| PKR4128BPIA | 制造商:Ericsson 功能描述: |
| PKR4128BPIC | 制造商:Ericsson 功能描述: |
| PKR4128BSI | 功能描述:DC/DC转换器 3.3 5Vdc Isolated Input 36-75V 13W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PKR4128BSIA | 制造商:Ericsson 功能描述: |
发布紧急采购，3分钟左右您将得到回复。