- 您现在的位置：买卖IC网 > PDF目录17091 > PMF18WE1 (Microchip Technology)PROCESSOR MODULE FOR ICE4000 PDF资料下载
参数资料
| 型号： | PMF18WE1 |
| 厂商： | Microchip Technology |
| 文件页数： | 19/98页 |
| 文件大小： | 0K |
| 描述： | PROCESSOR MODULE FOR ICE4000 |
| 标准包装： | 1 |
| 模块/板类型： | 处理器模块 |
| 适用于相关产品： | ICE4000 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页
Installation
2.8
SOFTWARE SETUP
1. Launch MPLAB IDE v6.xx.
2. From the Configure menu, select Select Device. In this dialog, choose the device
you will be emulating and click OK .
3. From the Debugger menu, select Select Tool and then MPLAB ICE 4000 to
enable the emulator.
Note:
If you cannot select the emulator as the debug tool, please see
Once you have selected MPLAB ICE 4000, debug options will appear on the
Debugger menu.
Note:
It is recommended that you not have a programmer enabled at the
same time as the emulator. See Appendix A. “Troubleshooting” for
more information.
4. The default port setting is USB = ICEUSB-0. If you wish to change this settings,
you may do so on the Port tab of the Debugger>Settings dialog. See
5. MPLAB ICE 4000 allows the emulator processor module to be powered by either
the emulator pod or the target system. This is set up in MPLAB IDE as follows:
? Emulator pod: Debugger>Settings , Power tab, “Processor Power From
Emulator”
? Target system: Debugger>Settings , Power tab, “Processor Power From
Target Board”
Note:
You must select “Processor Power From Target Board” when using
low-voltage emulation.
See Section 3.5 “Selecting Processor Power” for more information. Also,
refer to the MPLAB ICE 4000 Processor Module and Device Adapter Specifica-
tion for processor module power requirements before configuring the system for
target system power.
When connecting to a target application system, you may notice a voltage level
on the target application, even though you have not yet applied power to the tar-
get application circuit. This is normal and is due to current leakage of protection
diodes through V CC of the Device Adapter. The current leakage will typically be
less than 20 mA. However, if the target application is using a voltage regulator, it
should be noted that some regulators require the use of an external shunt diode
between V IN and V OUT for reverse-bias protection. Refer to the manufacture’s
data sheets for additional information.
MPLAB ICE 4000 should now be ready for you to use as an emulator. If you have had
problems, please consult Appendix A. “Troubleshooting” . Otherwise, proceed to the
next chapter for additional software setup considerations.
? 2004 Microchip Technology Inc.
DS51490A-page 13
相关PDF资料 |
PDF描述 |
|---|---|
| ECM18DRTN-S13 | CONN EDGECARD 36POS .156 EXTEND |
| 0210490266 | CABLE JUMPER 1.25MM .152M 20POS |
| HW-V5-ML510-G | BOARD EVAL FOR VIRTEX-5 ML510 |
| SDR-T | SCOTCH CODE REFILL T |
| RCM12DTKT | CONN EDGECARD 24POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PMF18WF0 | 功能描述:插座和适配器 Processor Module RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| PMF18WH0 | 功能描述:插座和适配器 PIC18F ICE4000 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| PMF18WJ0 | 功能描述:插座和适配器 Processor MOD RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| PMF18WJ1 | 功能描述:插座和适配器 Processor Module RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| PMF18WK0 | 功能描述:插座和适配器 PIC18F RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
发布紧急采购，3分钟左右您将得到回复。